Manual Christopeit Walker 9101 (page 14 of 36) (English, German, Dutch, French)

793215

Zoom out

Zoom in

1/36

Assembly Instructions

Remove all the separate parts from the packaging, lay them on the ﬂoor

and check that all are there on the base of the assembly steps in these

instructions for assembly and use. Please note that a number of parts

have been connected directly to the main frame and preassembled.

In addition, there are several other individual parts that have been

attached

to separate units. This will make it easier and quicker for you to

assemble the equipment. Assembly time: 15 min.

Step 1:

Attach the rear foot tube (9) at main frame (1).

1. Put the pre-assembled main frame in horizontally position on the ﬂoor

and fold down the front foot tube (2) into front position. Secure this

position by using safety pin (41) as picture “A” shows.

2. Attach the rear foot (9) with height adjustable foot caps (27) to the

main frame (1). Do this with the two screws M8x75 (13), washers 8//25

(18), and cap nuts (25). After assembly has been completed, you can

compensate for minor irregularities in the ﬂoor by turning the wheel at

cap (27). The equipment should be set up that the equipment does not

move of its own accord during a training session.

3. Put the foot pedal (7) into lowest position and secure with handgrip

screw M8x15 (37) as picture “B” shows.

Step 2:

Assembly of hand grips (6L+6R) at connection tube 1 (4L+4R).

1. Put the hand grips left and right (6L+6R) against the connection tubes

1(4L+4R) as picture shows, so that the holes are align. (Handgrip left

with magnet (43) on left side.) Put one washer 8//16 (22) on each screw

M8x80 (14) and tighten the hand grips (6L+6R) at connection tube 1

(4L+4R) again washer 8//16 (22) and self locking nut (24).

(Note: Don’t tighten too much, the handgrips needs easy moving for

fold up function,)

2. Put the handgrip screw M8x60 (38) through the upper holes and screw

the hand grips (6L+6R) at connection tube 1 (4L+4R) tightly.

Step 3:

Assembly of computer (42) and pad (12).

1. Put the pad (12) against the pad holder (10) as picture „A“ shows and

tighten it into desired vertically position with hand grip screw M8x30

(39).

2. Push the pad holder (10) into appropriate position at computer holder

(3) and secure with hand grip screw M8x40 (36) into desired horizontally

position.

3. Take the computer (42) that has been supplied out of the packaging and

insert the batteries (Type “AA”-1.5 V pen cells) by watching for the right

polarity on the back of the computer (42). (Batteries for the computer

are not included in this item. Please buy them at your located market.)

Attach the computer (42) at computer holder (3).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit Walker 9101 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit Walker 9101 Manual

Product: