793207
23
Zoom out
Zoom in
Previous page
1/60
Next page
23
Meanings of error message codes
In case of malfunctions may adjoining list of error messages help for people to get function back. Basically, electrical repairs only in compliance with the
relevant safety rules which exists. For more information and assistance in case of malfunctions with our service department (contact details see last page.)
Error code Possible Reason Solutions
------- the safety lock is removed 1. Put the safety lock well
2. Change the safety lock switch or magnetic sensors in the computer.
3. If it’s still not ok , than change the computer
E01 Communication abnormality: abnormal commu-
nication between the controller and the electro-
nic meter after powering on
1. Switch off the treadmill and plug out AC cable
2. Check each section of connection of the communication wires from the electronic
meter to the controller and ensure that all core wires are well connected.
3. Check whether wirings between the electronic meter and the controller are dama-
ged; if yes, replace the damaged wire.
E02 Explosion-proof protection: 1. Switch off the treadmill and plug out AC cable
2. Check whether the power supply voltage is less than 50% of the normal value.
please ensure correct voltage and test again.
3. Check whether the controller emits the odor of burning; if yes, replace the con-
troller.
4. Check whether motor wires are well connected; re-connect motor wires.
E03 No sensor signal: 1. Switch off the treadmill and plug out AC cable
2. Check whether the sensor connector is well plugged or whether it is damaged;
plug it well or replace the sensor.
E05 Over-current protection: 1.Check whether power supply voltage specifications is inconsistent or too low and
use correct voltage specifications for re-test.
2. System self-protection is triggered under excessive current caused by the
excessive load more than the rated value, or some place of the treadmill is jammed
so that the motor can not rotate; thus, the system start up self-protection against
excessive current under excessive load; adjust the treadmill and restart it.
3. Check whether there is over-current sound or burning odor when the motor is
running; replace the motor.
4. Check whether the controller emits abnormal odor; replace it if yes.
electronic
meter has no
display.
the communication wire from the electronic
meter to the controller is not well connected or
the transformer is damaged
1. Switch off the treadmill and plug out AC cable
2. Dismantle the pillar to check connection joints on each section of the wiring from
the electronic meter to the controller.
3. Ensure that each wire core is well connected.
4. or the reason may be the communication power cord defect (damaged or broke
down); in such case, re-connect or replace wires; or replace a transformer.
E09 Controller is in tilt position 1. When treadmill has incline position no start possible
2. Treadmill is not fold out complete on an even floor
3. Tilt switch at PC board has problem
Note:
Please contact your local dealer if you have checked all the
above listed things but the problem is still there.
Training area in mm
(for home trainer and user)
Free area in mm
(Training area and security area
(rotating 60cm))
English
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit TM500S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit TM500S in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info