In case of malfunctions may adjoining list of error messages help for people to get function back. Basically, electrical repairs only in compliance with the
relevant safety rules which exists. For more information and assistance in case of malfunctions with our service department (contact details see last page.)
Note:
Please contact your local dealer if you have checked all the above listed
things but the problem is still there.
Problem Potential reasons Solutions
-------Safe lock falls down1. Place back the safe lock;
2. Replace safe lock switch or magnetic sensor in the electronic meter; if the problem still fails to
be solved, replace the electronic meter;
E01After powering on, the electronic me-
ter displays E01
Communication failure from the
electronic meter to the driver, The
electronic meter displays E01 in the
operating process Communication
failure from the driver to the electro-
nic meter
1. Check whether the connecting joint between the electronic meter and the core wire of the con-
troller is loose; whether wires are damaged; whether the core wires are in correct connecting order.
2. The controller may be defective. Check and replace a good one.
3. The electronic controller’s IC may not be plugged to the place. Check and ensure good plugging.
4. The transformer may be damaged. Check and replace a good one.
E02Explosion-proof protection or motor
abnormality
1. Check whether the power supply voltage is less than 50% of the normal value; please ensure
correct voltage and test again;
2 Check whether motor wires are well connected; re-connect motor wires, or, if the problem still
fails to be solved, replace the motor;
3. Check whether there is peculiar odor generated by the controller; if yes, it means that IGBT has
been broken down to cause short circuit; then, replace the controller.
E03No sensory signal Check whether the photoelectric sensor directs to the hole on CD; check whether wires of photo-
electric sensor are damaged and whether terminals of the photoelectric sensor and speed termi-
nals on the controller are firmly connected.
E04Lifting learning or self-inspection
fails
1. Check whether motor signal wires are well inserted; re-insert the signal wire joint to ensure that
it is reliable;
2. Check whether lifting motor‘s AC wires are properly connected; lifting motor shall be correctly
plugged according to marks on its AC controller;
3. Check whether motor wiring is damaged to form open circuit; if yes, replace wires or replace the
lifting motor;
4. Replace the controller;
5. After all of these inspections, press the learning key for learning again.
E05Over-current protection 1. It may be the system’s self-protection against excessive current when the load exceeds the rated
value; restart the machine;
2. Some part of the treadmill is jammed so that the motor can not rotate, thus triggering the self-
protection of the system against excessive current under excessive load; adjust the treadmill and
restart it, or add lubricant.
3. Check whether there is over-current sound or burning odor when the motor is running; replace
the motor;
4. Check whether the controller emits the odor of burning; if yes, replace the controller.
E06Lifting sensor has no signal1. Check whether lifting signal wires are damaged.
2. Check whether lifting signal terminals and the controller’s lifting terminals are firmly connected.
3. Check whether lifting power cords are damaged.
4. Check whether lifting power cord terminals and the controller’s lifting terminals are firmly con-
nected.
No display
on the elec-
tronic meter
The controller is not powered on or
is damaged
1. First of all, check whether the over-load protector has tripped off; if yes, press it;
2. Check the power supply switch, over-load protector and the controller’s power cord and trans-
former to ensure well connection;
3. Check whether the power cords from the electronic meter to the controller are well collected;
dismantle the pillar to check connecting joints on each section of the wiring from the electronic me-
ter to the controller; ensure that each wire core is well connected; or the reason may be the com-
munication power cord defect (damaged or broke down); in such case, re-connect or replace wires.
4. The transformer is damaged; replace the transformer
E09Controller is in tilt position1. When treadmill has incline position no start possible
2. Treadmill is not fold out complete on an even floor
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Christopeit TM450S at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Christopeit TM450S in the language / languages: English, German, Dutch, French as an attachment in your email.
The manual is 5.59 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
