585822
24
Zoom out
Zoom in
Previous page
1/48
Next page
24
Step 9:
Installation of cable 2 for lattissimus (40) with pulleys (19).
1. Put the cable 2 for latissimus (40) with screw end through the
top frame (11) so that the ball of cable 2 (40) is below of top frame
(11). Then put it through the second big hole of top frame (11) and
through top cover bracket (82). Finally screw I into the pull rod (36)
as arrows shows on figure.
2. Attach the two pulleys (19) with cable 2 (40) into the top frame
(11) and secure with hex bolts M10x70 (48) and nylon nuts M10 (64).
3. Attach two pulleys (19) with cable 2 (40) and pulley covers (20)
into double pulley holder (25) and secure with hex bolt M10x50 (50),
washer 10//20 (67) and nylon nut M10 (64)
4. Attach one pulley (19) with cable 2 (40) and pulley cover (20) into
pulley holder at top frame (11) and secure with hex bolt M10x50
(50), washer 10//20 (67) and nylon nut M10 (64).
5. Cover all screw heads of screws (48+50) and nuts (64) with
corresponding screw caps (74).
6. Connect the latissimus bar (15) at cable 2 (40) by using carbine
hook (3) after assembly complete. To storage the long bar (15) you
can put it on the appropriate holder in front of the top fame (11).
Step 10:
Installation of cable 3 for leg curler (39) with pulleys (19).
1. Put the cable 3 for leg curler (39) with eye end through the leg
curler (4) so that the ball of cable 3 (39) is in front of the leg curl
(4) and put the cable 3 (39) with eye end through and big hole of
main frame (34).
2. Attach one pulley (19) with cable 3 (39) into the leg curler (4) and
secure with bolt M10x50 (50), washer 10//20 (67) and nylon nut
M10 (64).
3. Attach one pulley (19) with cable 3 (39) at main frame (34) and
secure with bolt M10x50 (50), washer 10//20 (67) and nylon nut
M10 (64).
4. Attach one pulley (19) with cable 3 (39) and pulley covers (20) into
bottom part of twisted pulley holder (26) and secure with hex bolt
M10x50 (50), washer 10//20 (67) and nylon nut M10 (64).
5. Attach one pulley (19) with cable 3 (39) and pulley covers (20) at
base frame (17) and secure with bolt M10x50 (50), washer 10//20
(67) and nylon nut M10 (64).
6. Put the cable 3 (39) with eye end through the double pulley holder
(25) and enlarge the length of cable 3 (39) with two carbine hooks
(3) and short chain (46) to connect it finally at appropriate
position of base frame (17).
7. Cover all screw heads of screws (50) and nuts (64) with
corresponding screw caps (74).
8. Connect the curl bar (12) at cable 3 (39) by using the
long chain (45) and carbine hooks (3).
(Note: When you use leg curler for exercising you should
disconnect the curl bar (12) with chain (45).
To get a smooth sliding cable system, you may adjust
the cable system roughly at short chain (46) with carbine
hooks (3) through setting them into another position. For
smaller adjustments you can use the screw end of cable
1 at pull rod. Always fix the position of this screw with nut
and take care that this screw is minimum 12mm inside the
threat. For an easier sliding of the weights at sliding tubes
(5) you can put a little bit lubrication oil at sliding tubes.)
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit SP 20 XL station at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit SP 20 XL station in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info