517240
15
Zoom out
Zoom in
Previous page
1/44
Next page
15
English
Assembly Instructions
Before beginning assembly, be sure to observe our recommendations
and safety instructions.
Step 1:
Installation of the left support (33) and the right support (24) on the
foot (23) with the screws M8x50 (58), the washers 8//16 (59) and the
cap nuts M8 (61).
1. Place the screws (58), the washers (59) and the nuts (61) accessibly
beside the foot (23).
2. Place the left support (33) on the foot and align so that the hole patterns
in the foot are aligned.
(Note: The transport rollers (21) pre-assembled in the foot (23) must point
backwards (opposite to the line of sight when standing on the machine
during training. Right and left are specifi ed as viewed standing on the ma-
chine during training.)
3. Push on each screw (58) a washer (59) and push them through each
hole.
4. Put a washer (25) on the end of each screw (58) and screw on a nut
(61).
5. Proceed as described in 1. – 4. with the right support (24) on the right
hand side of the foot (23).
Step 2
Installation of cover (38) at main frame (1) and cable (25)
at base of Magnet (18).
1. Put the tension cable (25) into the receiver of the base frame (1) and
insert the end of tension cable (25) into the base of magnet (15). Secure
the position of the tension cable (25) by screwing the nut at the end of the
tension cable in the indicated arrow direction. (See fi gure 1-3)
2. Screw the cover (38) at main frame (1) tightly, by using screws (47) and
washers (62).
Step 3:
Installation of the pre-assembled main frame unit (1) on the left (33)
and right (24) supports with the screws M8x50 (63), the washers 8//22
(64).
1. Place the screws (63), two washers (64) accessibly beside the foot (23).
2. Lay the main frame unit (1) between the supports (33) and (24) and align
so that the hole patterns in the main frame (1) and the supports (33+24)
are aligned. (Note: You should ask a second person to hold the main frame
unit (1) or support it with a suitable object to perform the following steps
of assembly.)
3. Place a washer (64) on each screw (63) and then push the screws
through the holes in the supports (24) and (33) and tighten the main frame
(1) fi rmly.
4. Push the ends of the sensor cable (42) (projecting from the main frame(1))
and sensor wire for support (68) (from the left support (33)) together.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit Runner Walking - 98294 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit Runner Walking - 98294 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info