793214
5
Zoom out
Zoom in
Previous page
1/28
Next page
5
DE

      -

Nehmen Sie den Computer (44) und stecken Sie das
Verbindungskabel (30) und die Pulsverbindungskabel
3 (45) in die entsprechenden Steckverbindung des
Computers (44) ein.
2. Legen Sie den Computer (44) auf die Computer-
aufnahme (5) und befesgen Sie diesen miels der
Schrauben M4x10 (24) und Unterlegscheiben 4//8
(52). (Bie Achten Sie darauf, dass die Kabel bei der
Montage des Computers nicht eingeklemmt werden.)

      

Stecken Sie den Sitzhebel (8) passend auf die Achse
(19) und schrauben Sie den Sitzhebel (8) miels der
beiden Schrauben M6x10 (22) fest. (Um den Sitz in
eine andere Posion zu verstellen ziehen Sie den Sitz-
hebel (8) nach oben. Um die Sitzposion fest zu set-
zen, drücken Sie den Sitzhebel (8) nach unten.)
 Schieben Sie die Sitzschiene (4) in entsprechen-
der Richtung durch die Sitzaufnahme (2). Achten Sie
dabei auf die richgen Befesgungspunkte vorne und
hinten.
 Legen Sie die Sitzschiene (4) mit Sitzaufnahme (2)
in die Aufnahmen am Grundrahmen ( 1 ) ein, sodass
die Bohrungen uchten. Schrauben Sie miels der
Schrauben M8x16 (14), Federringen (13) und Unter-
legscheiben 8//16 (15) die Sitzschiene (4) am Grund-
rahmen (1) fest.

-

1. Führen Sie die Computeraufnahme (5) mit dem un-
teren Ende zur Aufnahme am Grundrahmen (1) und
verbinden Sie die die Pulsverbindungskabel 3 (45) mit
den Pulsverbindungskabeln 2 (42) und das Verbin-
dungskabel (30) dem Stellmotorkabel (43).
Schieben Sie die Computeraufnahme (5) in die da-
für vorgesehene Aufnahme des Grundrahmens (1).
Achten Sie darauf, dass die zuvor hergestellte Kabel-
verbindungen nicht eingequetscht werden und rich-
ten Sie die Computeraufnahme (5) gerade aus. Auf
die Schrauben M8x16 (14) je einen Federring (13) und
eine gebogene Unterlegscheibe 8//20 (12) aufstecken
und damit die Computeraufnahme (5) am Grundrah-
men (1) festschrauben.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit RST 3200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit RST 3200 in the language / languages: English, German as an attachment in your email.

The manual is 4.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info