585808

Christopeit RS 2 Manual

18
Zoom out
Zoom in
Previous page
1/60
Next page
18
Assembly Instructions
Remove all the separate parts from the packaging, lay them on the floor
and check roughly that all are there on the base of the assembly steps.
Please note that a number of parts have been connected directly to
the main frame and preassembled. In addition, there are several other
individual parts that have been attached to separate units. This will make
it easier and quicker for you to assemble the equipment.
Step 1:
Preparing for assembly of main frame (1).
1. Take out the screws (20) from main frame (1) and pull out slowly the
seat frame (9) from main frame (1).
2. Screw into the threat holes the screws (20) with washers (21) at seat
frame (9).
Step 2:
Attach the stabilizer (2+3) and seat frame (9) at main frame (1).
1. Place the seat frame (9) near the main frame (1) and connect the plugs
of pulse connection cables 1 (10) and pulse connection cables 2 (26).
2. Push the seat frame (9) into the locator provided for it at the main frame
(1). Ensure that the cable connections made are not squashed. Screw
the seat frame (9) at the main frame (1) with screws (20), washers (21)
and spring washers (42).
3. Attach the front foot (2) with the preassembled transport rollers (7) to
the main frame (1). Do this with the two screws M8x75 (45), washers
(13), spring washers (42) and cap nuts (6).
4. Attach the rear foot (3) with preassembled end caps (8) to the seat frame
(9). Do this with the two screws M8x90 (4), washers (5), spring washers
(42) and cap nuts (6).
5. Screw in the rubber foot (35) into the appropriate threat of main frame
(1). After assembly has been completed, you can compensate for minor
irregularities in the floor by turning the wheel at end cap (8) and rubber
foot (35). The equipment should be set up that the equipment does not
move of its own accord during a training session. If you like to change
the position of the recumbent bike, lift up at rear foot (3) until you can
move easy on the front transportation rollers to another place.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit RS 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit RS 2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info