Manual Christopeit Omega (page 21 of 60) (English, German, Dutch, French)

602836

Zoom out

Zoom in

1/60

Step 3:

Installation of the pedal supports (32) with connecting tubes (19) and

pedals (38).

1. Place the handgrip axle (7) in the holder of handlebar support (10) and

push on each side one wave washer 17//25 (8) on axle’s end.

2. Place the preassembled unit of foot pedal support right (32R) and

connection tube right (19R) on right side next to the main frame and

push the smaller wave washer onto the pedal crank (70) on right side.

3. Push the connecting tube (19R) onto the handgrip axle (7) and the

pedal support holder (97R) onto the pedal crank (70) at the same time.

Put on the screw (23) a spring washer (28) and a big washer 8//38 (24)

and tighten the connection tube (19R) at hand grip axle (7) ﬁrmly. Then

tighten the pedal support holder (19R) at pedal crank (11) with screw

(23), spring washer (28) and a little bit smaller washer 8//28 (101).

4. Install the left pedal support left (32L) with connection tube (19L) incl.

all additionally required parts on the left hand side of the machine as

described in step 2-3.

5. Mount front pedal support cover (35L+35R) to both side front ends of

pedal supports (32L+32R) and secure with screws (33+34) each side.

6. Turn the assembled unit at pedal crank slowly for 3-4 rotations and

tighten now the screw connection of handlebar support of Step 2 ﬁrmly.

Push down the handlebar support cover (51) to cover up the screw

connection.

7. Put the pedals (38L+38R) onto the pedal holders (32L+32R). Adjust the

holes in the parts so that they aligned.

8. Push the screws (41) from above through the holes. Put on a washer (40)

from the opposite side and screw on a hand grip nut (39) and tighten

ﬁrmly. (Note: The right and left footrests (38) can discern by the edges

of the longitudinal sides of the footrests. The high edges of the footrests

(38) must point inwards (towards the main frame. The position adjusted

in this way should always be equal at both sides. The positions can

change as desired at all times by removing the carriage bolts (41) and

sliding the footrests on the footrest brackets to get a more or less ﬂat

movement.)

Step 4:

Installation of the handgrips (29) at the connecting tubes (19).

1. Put the handgrip bars (29L+29R) onto the connecting tubes (19L+19R)

and adjust the holes in the tubes so that they are aligned.

(Note: the handgrip bars must be aligned after assembly so that the

upper ends are inclined outwards (away from the support (10)).

2. Put on each bolt (21) a curved washer (3) and push the bolts (21) through

the holes and tighten the handgrip bars (29L+29R) at connection tubes

(19L+19R) with nut (27) ﬁrmly.

3. Place the bottle holder (5) into the appropriate position of handlebar

support (10) and ﬁx it with two screws (4).

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit Omega in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit Omega Manual

Product: