Manual Christopeit LB 50 plus - 1350 (page 17 of 44) (English, German, Dutch, French)

644105

Zoom out

Zoom in

1/44

English

USER MANUAL OF COMPUTER 1350

Display:

Speed:

Shows the current running speed in kilometers per hour. (0.8–

10.0km/h or 0,5-6,2mph)

Distance:

Shows the distance in kilometers of running. (0.00 - 99.9Km)

Calories:

Shows the approx. calories in kilocalories. (0.0 - 999 kcal.) (based

on 30kcal per Km)

Time:

Shows the time of exercising. (0:00 - 99:59Min.)

After reach value of 99:59Min the treadmill stops automatically.

Keys:

Start -key

Press this key to start the treadmill and after a countdown of 3 sec.

the running surface start move.

Stop -key

Press this key to stop the treadmill and the running surface stops

slowly.

„+“ –key:

Press this key to increase the speed of treadmill for 0,1km/h.

„-“ –key:

Press this key to decrease the speed of treadmill for 0,1km/h.

If you want to switch the computer data from km/h into mph

Please remove the safety clip (48) from computer (46) and press

key “+” and “-” at the same time for 2 seconds.

Meanings of error message codes:

Error code Possible Reason Solutions

------- the safety lock is removed 1. Put the safety lock well

2. Change the safety lock switch or magnetic sensors in the computer.

3. If it’s still not ok , than change the computer

E1 Communication abnormality: abnormal commu-

nication between the controller and the electro-

nic meter after powering on

1. Switch off the treadmill and plug out AC cable

2. Check each section of connection of the communication wires from the electronic

meter to the controller and ensure that all core wires are well connected.

3. Check whether wirings between the electronic meter and the controller are dama-

ged; if yes, replace the damaged wire.

E2 Explosion-proof protection: 1. Switch off the treadmill and plug out AC cable

2. Check whether the power supply voltage is less than 50% of the normal value.

please ensure correct voltage and test again.

3. Check whether the controller emits the odor of burning; if yes, replace the con-

troller.

4. Check whether motor wires are well connected; re-connect motor wires.

E3 No sensor signal: 1. Switch off the treadmill and plug out AC cable

2. Check whether the sensor connector is well plugged or whether it is damaged;

plug it well or replace the sensor.

E5 Over-current protection: 1.Check whether power supply voltage speciﬁcations is inconsistent or too low and

use correct voltage speciﬁcations for re-test.

2. System self-protection is triggered under excessive current caused by the

excessive load more than the rated value, or some place of the treadmill is jammed

so that the motor can not rotate; thus, the system start up self-protection against

excessive current under excessive load; adjust the treadmill and restart it.

3. Check whether there is over-current sound or burning odor when the motor is

running; replace the motor.

4. Check whether the controller emits abnormal odor; replace it if yes.

electronic

meter has no

display.

the communication wire from the electronic

meter to the controller is not well connected or

the transformer is damaged

1. Switch off the treadmill and plug out AC cable

2. Dismantle the pillar to check connection joints on each section of the wiring from

the electronic meter to the controller.

3. Ensure that each wire core is well connected.

4. or the reason may be the communication power cord defect (damaged or broke

down); in such case, re-connect or replace wires; or replace a transformer.

Note:

Please contact your local dealer if you have checked all the

above listed things but the problem is still there.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit LB 50 plus - 1350 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit LB 50 plus - 1350 Manual

Product: