644104

Christopeit CX3 - 1531 Manual

17
Zoom out
Zoom in
Previous page
1/56
Next page
17
English
Step 2:
Attach the support (2) at the main frame (1).
1. Place screws M8x16 (16), curved washers 8//20 (56) and spring
washers for M8 (52) accessibly beside the front part of the main
frame (1).
2. Place the lower end of the support (2) against the holder of main
frame (1). Plug the ends of the two computer cables (20) and
(18) projecting from (1) and support (2) together.
(Note: The computer cable harness (18) projecting from the
support (2) must not slide into the tube, as it is required for later
steps of installation.)
3. Connect the tension cable of resistance control (17) to the
bracket of lower section cable of tension (19) (See figure A1-A4).
Before this step of the installation, it is advisable to adjust the
resistance setting to the position, at which the cable extends
furthest from the sheath. Put the lowest part of cable (17) into
the small hook of lower tension cable (19) (figure A1). Pull it
(figure A2) until the small hook get in higher position (figure A3)
and then insert the cable (17) onto the bracket (19) (figure A4).
When joining the tubes, ensure that the cable connection is not
trapped.
4. Put one spring washer (52) and one washer (56) on each screw
(16). Push the screws (16) through the holes in the support (2),
screw into the threaded holes of the main frame (1) but don’t
tighten them firmly. (This screw connection point will screw
tightly at least in Step 4)
Assembly Instructions
Remove all the separate parts from the packaging, lay them
on the floor and check roughly that all are there on the base of
the assembly steps. Please note that a number of parts have
been connected directly to the main frame and preassembled.
In addition, there are several other individual parts that have
been attached to separate units. This will make it easier and
quicker for you to assemble the equipment.
Assembly time: 35 - 45 min.
Step 1:
Attach the stabilizer (3+4) at main frame (1).
1. Attach the front foot (3) with the preassembled end caps (11)
to the main frame (1). Do this with the two screws M10x60 (12),
curved washers 10//20 (13), spring washers for M10 (67) and
cap nuts M10 (14).
2. Attach the rear foot (4) with height adjustable foot caps (15) to
the main frame (1). Do this with the two screws M10x60 (12),
curved washers 10//20 (13), spring washers for M10 (67) and
cap nuts M10 (14). After assembly has been completed, you
can compensate for minor irregularities in the floor by turning
the eccentric cap (15). The equipment should be set up that the
equipment does not move of its own accord during a training
session.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CX3 - 1531 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CX3 - 1531 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info