517213
22
Zoom out
Zoom in
Previous page
1/76
Next page
22
Installation instructions
Before beginning with installation, be sure to observe our
recommendations and safety instructions.
Some parts are preassembled.
Step 1:
Installation of front foot (2) and rear foot (8) on the main frame (1).
1. Place the bolts (4) and each two washers (5), spring washers (6) and
nuts (7) ready for use beside the front and rear part of the main frame
(1).
2. Place the front foot (2) and rear foot (8) into the bracket of the main
frame (1) and align so that the hole patterns of the bracket and the
foots are in conformance.
(Note: The front foot caps with transport roller units (3) installed in the
front foot bar (2) must point forwards (as viewed when training, standing
on the machine).
3. Push one screw (4) each through the bores.
4. Install one washer (5) and one spring washer (6) each on the ends of
the screws (4) and fasten with one nut (7) each. (You can use adjustable
screw (67) to level the bike.)
Step 2:
Connecting the computer cables (13+14) and installation of handlebar
post (15).
1. Place the lower end of the handlebar post (15) against the main frame
(1). Connect the two ends of the computer cable (13) and (14) projecting
from (1) and (15).
2. When the electrical cable connections have been made, push the
handlebar post (15) into the main frame (1). (Note. When pushing the
tubes together, ensure that the electrical cable connection is not trap-
ped. The short tube welded crosswise to the upper end of the tubular
support (15) must point forwards (as viewed when training standing on
the machine).
3. Push one spring washer (6) and one washer (5) on each of the bolts
(12). Push the bolts (12) through the bores in the main frame (1), screw
into the threaded holes of the handlebar post (15) and tighten firmly.
Step 3:
Installation of the right (20) and left handgrip (18) on the handlebar post
(15) with the axle support (17).
1. Push the axle support (17) centrally into the tube welded crosswise to
the handlebar post (15).
2. Push on the handgrip (20) from the right hand side and the handgrip
(18) from the left hand side.
(Note. After installation, the handgrips must be aligned in such a manner
that the upper ends are inclined outwards (from handlebar post (15)).
3. Push one spring washer (6) and one washer (16) onto each screw (12),
screw the screws (12) into the threaded holes at both ends of the axle
support (17) and tighten firmly.
(Note. The handgrips are heavier at the top than at the bottom. Twist
the handgrips downwards until further installation is conducted.)
4. If the arms appear to move too much sideways, please carry out the
Following procedure; Remove the assembly bolt from either end of the
Metal shaft, place one or more of the 0.15mm spacers (A) provided on
to The shaft, as shown in the picture and then re-fit the assembly bolt.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CX 6 - 9126 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CX 6 - 9126 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info