Manual Christopeit CS 5 - 99257 (page 17 of 44) (English, German, Dutch, French)

517211

Zoom out

Zoom in

1/44

Computer instructions

The enclosed training computer provides high convenience in training. All

values relevant to the training are displayed in a corresponding window. From

the beginning of the training session onwards, the required time, the current

speed, the approximate energy consumption, the travelled distance and the

current pulse rate are displayed. All values are recorded incrementally for zero

upwards. If the training session is to last for a particular period, a particular

number of calories is to be consumed, a particular distance travelled and a

particular pulse rate not exceeded, these values can be entered individually

or as combinations.

The computer is switched on by brieﬂ y pressing one of the buttons or simply

by beginning a training session. Select the desired function for input by

pressing the „E“ button. The function which can be changed is displayed.

Each desired value can be entered by pressing the two arrow buttons. The

„+“ and „-“ button stand for an increasing value starting from zero and also

for a decreasing value starting from the maximum value.

To start the computer, simply begin your training session. The computer

then begins to measure and display all values.

To stop the computer, simply end the training session. The computer stops

all measurements and holds the last achieved values. The last reached

values in the functions TIME, CALORIES and KM are stored and training can

proceed with these values when the training session is resumed.

The computer switches off automatically approx. 4 minutes after the training

session has ended. All values reached by then are erased.

Displays:

1. „TIME“ display:

Usually, the currently required time is displayed in minutes and seconds. A

particular value can be speciﬁ ed using the „+“ and „-“ buttons. Is a particular

time has been speciﬁ ed, the remaining time is displayed. When the speciﬁ ed

time has elapsed, this is indicated by an acoustic signal.

In this function, the last reached time is stored until the computer switches

off. (Maximum limit of the display is 99.59 minutes.)

2. „KM/H“ display:

The current speed is displayed n kilometres per hour. A particular value

cannot be speciﬁ ed with the „+“ and „-“ buttons. The last achieved value

is not stored in this function.

(Upper limit of the display is 99.9 km/h)

3. „CALORY“ display:

The current amount of consumed calories is displayed. A particular value

can be speciﬁ ed with the „+“ and „-“ buttons. If a particular consumed

amount is speciﬁ ed, the amount of calories remaining to be consumed

is displayed. When the speciﬁ ed value is reached, this is indicted by an

acoustic signal.

In this function, the last reached time is stored until the computer switches

off. (Upper limit of the display is 999 calories)

4. „KM“ display:

The current value of the travelled kilometres is displayed. A particular value

can be speciﬁ ed with the „+“ and „-“ buttons. If a particular distance is

speciﬁ ed, the distance remaining to be travelled is displayed. When the

speciﬁ ed value is reached, this is indicated by an acoustic signal.

In this function, the last reached time is stored until the computer switches

off. (Upper limit of the display is 999 km)

5. „PULS“ display:

The current pulse rate is displayed in beats per minute. A particular value

can be speciﬁ ed with the „+“ and „-“ buttons.

If a particular pulse rate limit is reached, this is indicated by an acoustic

signal. In this function, the last reached time is stored until the computer

switches off.

(Upper limit of the display is 90- 220 pulse beats per minute)

6. „SCAN“ function :

If this function is selected, the current values of all functions are displayed

successively in a constant sequence approx. every 6 seconds.

Buttons:

1. „+“ and „-“ buttons:

The speciﬁ ed values of the individual functions can be entered in steps by

each pressing of these buttons. The desired function must ﬁ rstly be selected

using the „E“ button.

After training has begun, the display counts down from the speciﬁ ed value

to zero.

2. „E“ button:

By pressing this button brieﬂ y, it is possible to change from one function to

another, i.e. the respective functions can be selected in which entries are

to be made with the arrow buttons.

3. „F“ key:

Pressing this key once brieﬂ y makes it possible to change from one function

to another, i.e. the respective functions can be selected for which entries

can be made using the „E“ key. The currently selected function is indicated

by an icon in the respective window.

4. „L“ = Delete:

When this key is pressed brieﬂ y, the values chosen with the „E“ key are

reset to zero.

Holding the key pressed (approx. 5 seconds) allows all last attained values

to be deleted. All values of all displays are then set to zero.

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CS 5 - 99257 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit CS 5 - 99257 Manual

Product: