517207
14
Zoom out
Zoom in
Previous page
1/44
Next page
14
Assembly Instructions
Before beginning assembly, be sure to observe our recommendations
and safety instructions.
Step 1:
Install of the front footbar (57) and the rear footbar (31) on the main
frame (36) with the carriage bolts (30), the washers 8//20 (9) and the
cap nuts M8 (10).
1. Place screws (30) and two each washers (9), springwashers (70) and nuts
(10) accessibly beside the front and rear parts of the main frame (36).
2. Insert the foot bars (57) + (31) in the holder of the main frame (36) and
adjust so that the hole patterns of the holders and the foot bars (57) + (31)
are aligned.
3. Push one screw (30) through each hole.
4. Fit the screw ends of (36) with one washer (9), one springwasher (70) and
fasten each with a nut (10).
Step 2:
Connecting the computer cable harness (62) to the computer cable
harness (59), installation of the plastic cover (60) and rubber (61),
connecting lower tension cable (58) with tension control (65), installation
of the support (64) on the main frame (36) with the round-headed Allen
screws M8x15 (63), the washers 8//16 (9), and the spring washers for
M8 (70).
1. Place screws (63), each washers (9) and spring washers (70) accessibly
beside the front part of the main frame (36).
2. Place the lower end of the support (64) against the main frame (36) and
push the rubber (61) and plastic cover (60) onto the support (64).
Plug the ends of the two computer cable harnesses (62) and (59) projecting
from (36) and (64) together.
(Note: The computer cable harness (62) projecting from the support (64) must
not slide into the tube, as it is required for later steps of installation.)
When joining the tubes, ensure that the cable connection is not trapped.
3. Connect the middle section tension cable (65) to the bracket of lower
section cable tension (58) (See fi gure [1]-[3]). Before this step of the
installation, it is advisable to adjust the resistance setting to the highest
stage, at which the cable extends furthest from the sheath. Put the lowest
part of cable (58) into the small hook (fi gure 1). Pull it (fi gure 2)until the small
hook get in higher position and than insert the cable (58) onto the bracket
(65) (fi gure 3).
4. Put one spring washer (70) and one washer (9) on each screw (63). Push
the screws (63) through the holes in the support (64), screw into the threaded
holes of the main frame (36) and tighten fi rmly. (This screw connection point
will screw tightly at least in Step 5)
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CS 5 - 99254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CS 5 - 99254 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info