517203

Christopeit CPS 6 - 99062 Manual

14
Zoom out
Zoom in
Previous page
1/44
Next page
14
Assembly instructions
Remove all the separate parts from the packaging, lay them on thefl oor and
check that all are there on the basis of the packing list in these instructions for
assembly and use. Please note that a number of parts have been connected
directly to the main frame and preassembled. In addition, there are several
other individual parts that have been attached to separate units. This will
make it easier and quicker for you to assemble the equipment.
Step 1:
Attach the stabilizer (22) + (32) at main frame (21).
1. Attach the front foot (22) with the preassembled transport rollers (23)
to the main frame. Do this with the two screws (33), washers (18), spring
washers (24) and cap nuts (30).
2. Attach the rear foot (32) to the main frame. Do this with the two screws
(33), washers (18), spring washers (24) and cap nuts (30). After assembly
has been completed, you can compensate for minor irregularities in the fl oor
by turning the eccentric cap (34). The equipment should be set up that the
equipment does not move of its own accord during a training session.
Step 2:
Attach the pedal (26) at pedal crank (36).
1. Screw the right pedal (26R) into the locator in the right-hand side (as
seen in operation) for the pedal crank (36R) (warning! the screw direction
is clockwise).
2. Screw the left pedal (26L) into the locator in the left-hand side (as seen
in operation) for the pedal crank (36L)
(Warning! the screw direction is anti-clockwise).
3. Then mount the pedal straps left and right on the associated pedals (26).
(The pedals are signed with „L“ for Left and „R“ for Right.)
Step 3:
Attach the front post (12) at main frame (21).
1. Hold the handlebar support (12) with the computer cable (15) Against the
main frame holder. Connect the plug for the computer cable (15) coming
out of the bottom of the handlebar support (12) of the computer with the
matching plug for the sensor cable (55) coming out of the main frame
(21).
(Note: The computer cable harness (15) projecting from the support (12) must
not slide into the tube, as it is required for later steps of installation.)
2. Connect the middle section tension cable (56) to the bracket of lower
section cable tension (16) (See fi gure [1]-[3]). Before this step of the
installation, it is advisable to adjust the resistance setting to the highest
stage, at which the cable extends furthest from the sheath. Put the lowest
part of cable (16) into the small hook (fi gure 1). Pull it (fi gure 2)until the small
hook get in higher position and than insert the cable (16) onto the bracket
(56) (fi gure 3).
3. Place the handlebar support (12) in the locator provided for it in the
main frame (21). Ensure that the cable connections made in step 3 are not
squashed. When putting the steering tube in place, push the former slowly
down into the locator in the main frame. Screw the handlebar support (12)
onto the base frame (21) with the screws (17), spring washers (24) and
washers (18).
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CPS 6 - 99062 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CPS 6 - 99062 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info