644101

Christopeit CL1 - 1302 Manual

16
Zoom out
Zoom in
Previous page
1/40
Next page
16
Assembly Instructions
Remove all the separate parts from the packaging, lay them
on the floor and check roughly that all are there on the base of
the assembly steps. Please note that a number of parts have
been connected directly to the main frame and preassembled.
In addition, there are several other individual parts that have
been attached to separate units. This will make it easier and
quicker for you to assemble the equipment.
Step 1:
Install of front and rear foot (2+3) to the main frame (1).
1. Place two screws (13), washers (14) ), spring washers (25) and
nuts (15) accessibly beside the front and rear parts of the main
frame (1).
2. Insert the foot bars (2+3) in the holder of the main frame (1) and
adjust so that the hole patterns of the holders and the foot bars
(2+3) are aligned. The rear foot has preassembled eccentric caps
(12).
3. Push one screw (13) through each hole.
4. Fit the screw ends of (13) with one washer (14) and one spring
washer (25) each and fasten with a nut (15).
(Note: If the machine has positioned for training on an uneven
floor, this can be compensated at any place by turning the
eccentric caps (12).
Step 2:
Installation of right and left pedal (9R+9L) at pedal crank (10).
1. The pedals are marked “R” for right and “L” for left.
2. Screw the right pedal (9R) into the threaded hole on the right
hand side of the pedal crank (10) and tighten firmly.
(Note: Right and left are specifies as viewed seated on the
machine during training. It must also be observed that the
threaded part of the right pedal must be screwed clockwise
into the threaded hole of the pedal crank.)
3. Screw the left pedal (9L) into the threaded hole on the left hand
side of the pedal crank (10) and tighten firmly.
(Note: The threaded part of the left pedal have to screw
anticlockwise into the threaded hole of the pedal crank.)
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CL1 - 1302 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CL1 - 1302 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info