644097
17
Zoom out
Zoom in
Previous page
1/48
Next page
17
English
Step 3:
Installation of the pedal supports (31) and connecting tubes (38).
1. Place the Hand grip axle (58) in the holder of handlebar support (49).
2. Push the bottom end of connection tube right (38R) into holder of pedal
support right (31R) and adjust the holes in the tubes so that they are
aligned. (Note: Right is specified as viewed standing on the machine
during training.)
3. Push the bolt (29) through the holes of pedal support (31R) and distance
tube (34) of connection tube (38R) and tighten with washer (32) and nut
(26) firmly. (This connection point has to move easily. So please don’t
tighten the screw too much.)
4. Push the connecting tube (38R) onto the axles’ end of handlebar support
(58) and the pedal support holder (19) onto the pedal crank (11) at the
same time. Put on the screw (14) a washer 8//32 (36) and spring washer
(8) and tighten the connection tube (38R) at hand grip axle (58) firmly.
Then tighten the pedal support holder (19) at pedal crank (11) with screw
(14), washer 8//25 (15) and spring washer (8).
5. Install the left pedal support left (31L) and connection tube (38R) incl.
all additionally required parts on the left hand side of the machine as
described in step 2-4.
6. Mount front pedal support cover (28L+28R) to both
side front ends of pedal supports (31L+31R) and
secure with screws (27) each side.
7. Cover nut (21) and head of screw (18) with screw
cap (17).
8. Turn the assembled unit at pedal crank slowly for 2-3
rotations and tighten now the screw connection of
handlebar support of Step 2 firmly. Push down the
handlebar support cover (51) to cover up the screw
connection.
Step 4:
Installation of pedals (23) at pedal supports (31).
1. Push the pedals (23L+23R) onto the pedal holders (31L+31R). Adjust
the holes in the parts so that they are aligned.
2. Push the screws (22) from above through the holes. Push on a washer
(77) from the opposite side and screw on a hand grip nut (25) and tighten
firmly. (Note: The right and left footrests (23) can be discerned by the
edges of the longitudinal sides of the footrests. The high edges of the
footrests (23) must point inwards (towards the main frame. The position
adjusted in this way should always be equal at both sides. The positions
can be changed as desired at all times by removing the carriage bolts
(22) and sliding the footrests on the footrest brackets to get a more or
less flat movement.)
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit BS5 - 1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit BS5 - 1210 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info