644097

Christopeit BS5 - 1210 Manual

16
Zoom out
Zoom in
Previous page
1/48
Next page
16
Step 2:
Attach the front post (49) at main frame (1).
1. Push the handlebar support cover (51) onto the handlebar support (49).
2. Hold the handlebar support (49) with the computer cable (48) against the
main frame holder. Connect the plug for the computer cable (48) coming
out of the bottom of the handlebar support (49) with the matching plug
for the sensor cable (12) coming out of the main frame (1).
(Note: The computer cable harness (48) projecting from the support (49)
must not slide into the tube, as it is required for later steps of installation.)
3. Connect the cable of tension control (74) to the bracket of lower section
cable tension (75) (See figure [1]-[4]) Before this step of the installation,
it is advisable to adjust the resistance setting to the position, at which
the cable extends furthest from the sheath. Put the lowest part of cable
(74) into the small hook of lower tension cable (75) (figure 1+2). Pull it
(figure 3) until the small hook get in higher position (figure A3) and then
insert the cable (74) onto the bracket (75) (figure 4).
4. Place the handlebar support (49) in the locator provided for it in the main
frame (1). Ensure that the cable connections made are not squashed.
When putting the steering tube in place, push the former slowly down
into the locator in the main frame. Screw loosely the handlebar support
(48) onto the base frame (1) with the screws (39), spring washers (8) and
washers (7).(Attention: This screw connection will screw final tightly in
step 3)
Assembly Instructions
Remove all the separate parts from the packaging, lay them on the
floor and check roughly that all are there on the base of the assembly
steps. Please note that a number of parts have been connected directly
to the main frame and preassembled. In addition, there are several
other individual parts that have been attached to separate units. This
will make it easier and quicker for you to assemble the equipment.
Step 1:
Attach the stabilizer (2+3) at main frame (1).
1. Attach the front foot (2) with the preassembled transport rollers (4) to the
main frame (1). Do this with the two screws M8x75 (6), curved washers
(7), spring washers (8) and cap nuts (9).
Attention: Mount the front foot into right direction, so that the transport
rollers don’t touch the floor during exercising.
2. Attach the rear foot (3) with height adjustable foot caps (5) to the main
frame (1). Do this with the two screws M8x75 (6), curved washers (7),
spring washers (8) and cap nuts (9). After assembly has been completed,
you can compensate for minor irregularities in the floor by turning the
eccentric cap (5). The equipment should be set up that the equipment
does not move of its own accord during a training session.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit BS5 - 1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit BS5 - 1210 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info