Manual Christopeit Basic-Concept 9181 (page 15 of 48) (English, German, Dutch, French)

517197

Zoom out

Zoom in

1/48

Assembly Instructions

Before beginning assembly, be sure to observe our recommendations

and safety instructions.

Several items are pre-assembled.

Step 1:

Connecting the rear feet (1) to the crossframe (2) with the reinforcing

plates (59), the hexagonal bolts M10x70mm (38), the washers (52) and

the self-locking nuts M10 (49).

1. Place the rear feet (1), the crossframe (2), the screws (38), the washers

(52) and the nuts (49) accessibly.

2. Push one washer (52) onto each of the screws (38) and push from the

outside through the reinforcing plates (59) through the two rear feet

(1).

3. Join the crossframe (2) with the holes over the inserted screws so that

the longitudinal frame holder faces forwards and connect the whole

assembly by pushing on the washers (52) and lightly screwing on the

nuts (49).

4. Then tighten the previously made bolted connection ﬁ rmly and mount

the securing clips left (60) and right (61) with the washers (54) and the

self-locking nuts (62) on the rear feet (1).

5. Slide the adjusting bar (4) into one of three different positions at rear

foot (1)

Step 2:

Connecting the front foot (8) and the crossframe (2) to the longitudinal

frame (3) with hexagonal screws (39) + (40), washers (52) and the self-

locking nuts (49).

1. Place the front foot (8), the longitudinal frame (3), the screws (40), the

washers (52) and the nuts (49) accessibly.

2. Push a washer (52) onto each screw M10x25 (40) and push these from

the front through the front foot (8).

3. Join the longitudinal frame (3) with the holes over the inserted screws

and connect by pushing on the washers (52) and loosely screwing on

the nuts (49). Then tighten the bolted connection.

4. Insert the longitudinal frame (3) in the crossframe (2) so that the last

hole but one in the longitudinal frame (3) corresponds with the last

hole in the crossframe (2). Push a washer (52) onto the screw M10x60

(39) and push through the overlapping holes. Push a washer (52) onto

the end of the screw ant screw on the nut (49) until the self-locking

part of the nut engages on the thread of the screw (39) and the folding

mechanism is not blocked.

English

Step 3:

Installation of the crossbar (11) with the front foot (8) and the longitudinal

frame (3) with the hexagonal screws (46) + (48), washers (53) and nuts

(50).

1. Place the crossbar (11) with the screws (46) + (48), the washers (53)

and the nuts (50) accessibly.

2. Place a washer (53) on each of the screws (46) + (48). Hold the crossbar

with the hole over the fastening point on the front foot (8) and screw

on loosely with the screw (46).

3. Align the crossbar (11) with the second hole over the fastening point

on the longitudinal frame (3) and fasten loosely with the screw (48), the

washers (53) and the nut (50).

4. Then tighten the loosely made bolted connection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit Basic-Concept 9181 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit Basic-Concept 9181 Manual

Product: