Manual Christopeit Basic-Concept 9881 (page 16 of 48) (English, German, Dutch, French)

517196

Zoom out

Zoom in

1/48

Step 5:

Installation of the leg curler (10), the round pad holders (19) and the

round pads (20) on the front foot (8) with the sliding bearing (25), the

shaft piece (44) and the Allen screw (55).

1. Insert two sliding bearings (25) in the middle of the leg curler (10). Insert

the leg curler in the holder of the foot (8). Align the holes in the holder

and the sliding bearings. Push the shaft piece (44) through from one

side. From the opposite side, screw the screw (45) into the threaded

hole of the shaft piece and tighten ﬁ rmly.

(Note: After installation, the holder of the foot (8) must not be bent and

the leg curler must move easily.)

2. Push the two round padding holders (19) centrally into the correspon-

ding holes of the leg curler (10). Push on a round pad (20+20a) from

each side.

3. Finally, push a spring circlip 1 (27) on the bar bell weight holders of the

leg curler (10).

Step 4:

Installation of the butterﬂ y arms (5) incl. the left and right handgrips (6)

and (7) on the rear feet (1) with the hexagonal screws (43), the carriage

bolts (42), the sliding bearing (25), the washers (52), spacer nut (37), the

handgrip nut (85) and the self-locking nuts (49).

1. Place the parts named above near the feet (1). Insert two sliding

bearings (25) in the middle of the butterﬂ y arm (5). Put a washer (52)

on a screw (43), push the screw through the bearings and screw on a

nut (37) from the back.

(Note: Tighten the nut (37) only sufﬁ ciently to allow the screw (38) to

be easily turned.)

2. Push the end of screw (43) through the corresponding hole in the right

foot (1). Put on a washer (52), screw on a the handgrip nut (65) and

tighten ﬁ rmly.

(Note: The butterﬂ y arm (5) must move easily after installation.)

3. Insert two sliding bearings (25) in the upper end of the butterﬂ y arm

(5). Align the holes in the U-section of the handgrip (7) with the holes in

the sliding bearings (25), push through the screw (42) and fasten with

the washers (52) and the nuts (49).

(Note: The end of the handgrip (7) must point forwards after installation.

The line of sight is speciﬁ ed as viewed seated on the machine during

training.)

4. Install the second butterﬂ y arm (5) and the handgrip (6) at the left side

on foot 1 as described in 1. To 3.

5. Finally, push a spring circlip 1 (27) on the bar bell weight holders of the

butterﬂ y arms.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit Basic-Concept 9881 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit Basic-Concept 9881 Manual

Product: