644073

Christopeit AL5 - 1124 Manual

16
Zoom out
Zoom in
Previous page
1/44
Next page
16
Step 3:
Installation of the pedal supports (16) and connecting tubes (24).
1. Place the preassembled unit of the right pedal support (16) and one
connecting tube (24R) at the right hand side of the main frame (1).
(Note: Right is specified as viewed standing on the machine during
training.)
2. Put one wave washer (26) onto the pedal crank (21).
3. Push the connecting tube (24R) onto the axles’ end of handlebar support
(38) and put the pedal holder (16) at the pedal axle (21) at the same time.
Put on the screw (27) a washer 8//32 (13) and tighten the connection
tube (24R) at handlebar post (38) firmly. Then tighten the pedal support
holder (8R) at pedal crank (21) with washer 10//32 (45), spring washer
( 9) and self locking nut (10).
4. Cover nut (10) with a screw cap for M10 (11) and screw (27) with screw
cap for M8 (22).
5. Install the left pedal support (16) incl. all additionally required parts on
the left hand side of the machine as described in 1. – 4.
Step 4:
Installation of pedals (18L+18R) at pedal support (16).
1. Push the right pedal (18L+18R) onto the right pedal holder (16). Adjust
the holes in the parts so that they are aligned.
2. Push the screws (19) from above through the holes. Push on a washer
(14) from the opposite side and screw on a nut (50) and tighten firmly.
(Note: The right and left footrests (18) can be discerned by the edges of
the longitudinal sides of the footrests. The high edges of the footrests
(18) must point inwards (towards the main frame.)
Step 5:
Installation of the hand grips (28) at the connecting tubes (24).
1. Put the handgrip bars (28L+28R) onto the connecting tubes (24) and
adjust the holes in the tubes so that they are aligned.
(Note: the handgrip bars must be aligned after assembly so that the
upper ends are inclined outwards (away from the support (38)).
2. Push the bolts M8x20 (29) through the holes and tighten the handgrip
bars (28) with curved washers 8//19 (49) and spring washers (42) at
connection tubes (24) firmly.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit AL5 - 1124 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit AL5 - 1124 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info