518778
16
Zoom out
Zoom in
Previous page
1/48
Next page
16
Assembly Instructions
Remove all the separate parts from the packaging, lay them on the floor
and check roughly that all are there on the base of the assembly steps.
Please note that a number of parts have been connected directly to
the main frame and preassembled. In addition, there are several other
individual parts that have been attached to separate units. This will make
it easier and quicker for you to assemble the equipment.
Step 1:
Attach the stabilizer (20+27) at main frame (1).
1. Put the end caps with transportation roller (18) at the ends of front foot
(20) in appropriate position and screw them tightly by using screw (71).
2. Attach the front foot (20) with the preassembled end caps with
transportation rollers (18) to the main frame (1). Do this with the two
screws (28), washers (13), spring washers (37) and cap nuts (19).
3. Put the end caps with height adjustment (26) at the ends of rear foot
(27) and screw them tightly by using screw (71).
4. Attach the rear foot (27) to the main frame (1). Do this with the two screws
(28), washers (13), spring washers (37) and cap nuts (19). After assembly
has been completed, you can compensate for minor irregularities in the
floor by turning the wheel at cap (26). The equipment should be set up
that the equipment does not move of its own accord during a training
session. If you like to change the position of the home bike, put one foot
in front of the front foot (20) and pull at handlebar in front direction until
the home bike can move easy on the transportation rollers to another
place.
Step 2:
Attach the pedals (22L+22R) at pedal crank (21L+21R).
1. Screw the right pedal (22R) into the locator in the right-hand side (as
seen in operation) for the pedal crank (21R) (warning! the screw direction
is clockwise).
2. Screw the left pedal (22L) into the locator in the left-hand side (as seen
in operation) for the pedal crank (21L)
(Warning! the screw direction is anti-clockwise).
3. Then mount the pedal straps left and right on the associated pedals
(22). (The pedals are signed with „L“ for Left and „R“ for Right.)
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit AL 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit AL 1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info