793218
11
Zoom out
Zoom in
Previous page
1/40
Next page
11
GB


-




 Put the front stabilizer (1) at front support tube (3) so that the ho-
les align. Put onto the screws M8x20 (15) one washer 8//16 (18) and
screw the front stabilizer (1) at front support tube (3) ghtly.
 Put the rear stabilizer (2) at rear support tube (4) so that the holes
align. Put on the screws (15) one washer (18) and screw the rear stabi-
lizer (2) at rear support tube (4) ghtly.
 Put the rear support tube (4) into holder at front support tube
(3) so that the holes align. Put on the screw M10x70 (13) one was-
her 10//20 (17) and connect the rear support tube (4) at front support
tube (3) by using further washers (17) and nylon nut M10 (20). (Aen-
on: Don’t ghten too much this connecon point so that the fold up
funcon is without clamp eect.)
 Place the locking pin (22) through the holes and lock up this posi-
on. For using the fold up funcon pull out the locking pin (22).
 Place the leg pad support (5) at front support tube (3) so that the
holes align. Put onto the screws M10x70 (13) one washer 10//20 (17)
and screw the leg pad support (5) at front support tube (3) ghtly by
using further washers (17), reinforcement plate (10) and nylon nuts
M10 (20).
 Push the foam pad holder (9) into desired posion at leg pad sup-
port (5) in the middle and push on both ends of foam pad holder (9)
one leg foam pad (11).
 Place the cushion (12) onto cushion holder (6), so that the holes of
cushion holder (6) and thread of cushion (12) are align.
 Put onto the screws M6x20 (16) one washer 6//12 (19) and screw
the cushion (12) at cushion holder (6) ghtly.
 Put onto the screws M10x60 (14) one washer 10//20 (17) and put
the screws (14) through the holes at right hand grip (8). Put the right
hand grip (8) with the screws through the holes at cushion holder (6)
and put on opposite side the le hand grip (7) and further washers (17)
and nylon nuts M10 (20) to ghten this screw connecon.






14 17
17 20
17 20
14 17
19
16
6
8
7
12
13
13
17
17
17
20
3
9
11
11
5
10
31
31
32
31
31
15 18
18 15
18 15
20 17
17 13
15 18
15
18
15
18
22
1
2
3
4
31
31
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit AB 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit AB 1000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info