Manual Chicco Urban (page 23 of 80) (All languages)

768901

Zoom out

Zoom in

1/80

not fitted with the hood or sun canopy to

prevent the risk of suffocation.

· To prevent the risk of overheating or

suffocation, never leave the stroller

under the sun with the rain cover fitted

to it.

· Use only the rain cover supplied or

approved by the manufacturer.

· Prevent the stroller from coming into

contact with salt water. It may cause the

formation of rust.

· Do not use the stroller on the beach.

· When not in use, the stroller must be

kept away from the reach of children.

LIST OF COMPONENTS

· Frame

· Seat

· 2 rear wheels

· 2 front wheels

· Bumper bar

· Basket

· Mattress for pram configuration

· Raincover

With the “COLOUR PACK” (not part of the basic stroller

configuration, available to purchase separately), you will also have

the following components:

· Canopy

· Seat insert

· 2 shoulder strap pads and one crotch strap cover pad (comfort

kit)

· Legcover / Pram apron.

To assemble these components please refer to paragraph

“COLOUR PACK”.

NOTE: A Chicco Autofix Fast or Chicco Keyfit car seat can be

installed on the Urban stroller, using the specific “Car seat

adapter” (sold separately). To properly assemble the ‘’Car seat

adapter’’, refer to the relative instruction manual.

ADVICES FOR CLEANING AND MAINTENANCE

This product requires periodical maintenance. Cleaning and

maintenance operations must be performed exclusively by an

adult.

CLEANING

The lining of the stroller and the carrycot cannot be removed.

Clean the fabric parts using a wet sponge and neutral soap. Clean

the plastic parts periodically using a wet cloth. Dry the metal

parts if they come into contact with water in order to avoid the

formation of rust. Do not use solvents or abrasive products.

The padded mattress of the carrycot with removable lining can be

washed following the indications included in the materials label.

To clean the components of the Colour pack (purchased

separately), follow the indications included on the materials labels.

The washing symbols and relative meanings are indicated below:

Wash by hand in cold water

Do not bleach.

Do not tumble dry.

Do not iron.

Do not dry clean.

MAINTENANCE

Lubricate the removable parts with dry silicon oil if needed. Check

the state of wear of the wheels on a regular basis, and keep them

clean from dust and sand. Make sure that all plastic parts that slide

on the metal tubes are clean from dust, dirt and sand, in order to

avoid frictions that may compromise the optimal performance of

the stroller. Keep the stroller in a dry place.

FIRST ASSEMBLY OF THE STROLLER

1. Press the grey button inside the circular articulated joint and at

the same time, rotate the handle tube as shown in figure 1.

2. Then extend the structure completely, by opening the front leg

tube until hearing a locking click (fig. 2-2A).

3. Insert the front wheel into the relative hole until hearing a

locking click (fig. 3). Repeat the same operation for the second

front wheel.

4. To assemble the rear wheels Insert the wheel’s pin into the rear

leg tube as shown in fig. 4. Repeat the same operation for the other

wheel.

WARNING: Before using the stroller, make sure that the wheels

are well secured to the structure.

5. The front part of the basket has a shaped area. Assemble the

basket positioning the shaped part on the front tube, using the

relative press stud buttons (fig. 5) and repeat the operation for the

rear part of the basket (fig. 5A). To complete the assembly, thread

the straps located on the front part of the basket through the ‘’D’’-

shaped rings located on the front legs of the stroller, securing the

straps with the press stud buttons (fig. 5B).

WARNING: Do not load the basket with weights exceeding 3 kg.

ASSEMBLY OF THE SEAT: STROLLER CONFIGURATION

The packaging includes the disassembled stroller’s frame and seat.

6. To assemble the seat, position the metal support located on the

base of the seat as shown in fig. 6.

Then close the zip located at the bottom of the seat, wrapping the

metal component (fig. 6A).

7. Fasten buckle A located externally in the seat’s foot area, as

shown in Fig. 7, then fasten buckle B positioned externally under

the seat (fig. 7A) and tension the belt acting as shown in Fig. 7B.

WARNING: Check the belt’s tension on a regular basis.

8. To attach the seat, introduce the two hooks shown in Fig. 8 in

the relative slots located inside the circular articulated joints of

the stroller (fig. 8A) until hearing a locking click.

WARNING: Make sure the seat is installed properly by pulling it

upward.

9. The seat can be assembled on the stroller in both directions:

in forward facing configuration (Fig. 9) and parent facing

configuration (fig. 9A).

10. To remove the seat, press the grey side buttons and pull

upward (fig. 10). These operations must not be performed when

the child is inside the seat.

WARNING: Do not remove the seat from the stroller when the

child is inside of it.

SEAT ADJUSTMENTS

Once the seat is assembled on the frame, it can be adjusted in

three different positions.

11. The entire seat can be adjusted by pressing simultaneously the

buttons located above the central articulated joint (fig. 11).

12. The angle of the backrest can be adjusted compared to the

seat, by pressing the clip as shown in fig. 12.

LEG REST ADJUSTMENTS

13. It is possible to adjust the leg rest in various positions, by

pressing simultaneously the buttons shown in fig. 13.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Chicco Urban in the language / languages: All languages as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Chicco Urban Manual

Product: