747192
27
Zoom out
Zoom in
Previous page
1/78
Next page
27
4.1.6.3. DC 4-wire: DC-4W
Connect the N terminal to the common conductor.
Connect the VE/GND terminal to the earth.
Connect the V1 terminal to the +1 conductor.
Connect the V2 terminal to the +2 conductor.
Connect the V3 terminal to the +3 conductor.
Connect the IN current sensor to the common conductor.
Connect the current sensor I1 to the +1 conductor.
Connect the current sensor I2 to the +2 conductor.
Connect the current sensor I3 to the +3 conductor.
Always check that the arrow of the current sensor
points towards the load. This ensures that the phase
angle will be correct for power measurements and
other measurements that depend on the phase.
Figure 30
4.2. RECORDING
To start recording:
Check that there is in fact an SD card (not locked and not full) in the PEL.
Press the Selection key and hold it down. The REC, and indicators light in turn for 3 seconds each.
Release the Selection key while the REC indicator is lit. Recording starts and the REC indicator starts blinking twice
every 5 seconds.
To stop recording, proceed in exactly the same way. The REC indicator starts blinking once every 5 seconds.
It is possible to manage recording from PEL Transfer (see § 5).
4.3. MEASURED-VALUE DISPLAY MODES
The PEL has 4 display modes, represented by the icons at the bottom of the display unit. To change from one mode to the other,
use the or key.
Icon Display mode
Instantaneous values display mode: voltage (V), current (I), active power (P), reactive power (Q), apparent power
(S), frequency (f), power factor (PF), tan Φ.
Power and energy display mode: active energy of the load (Wh), reactive energy of the load (Varh), apparent
energy of the load (VAh).
Current and voltage harmonics display mode.
Maximum values display mode: maximum aggregated values of the measurements and energy of the last re-
cording.
The displays are accessible as soon as the PEL is on, but the values are zero. As soon as there is a voltage or current on the
inputs, the values are updated.
VN V3 V2 V1 VE/GND
IN I3 I2 I1
+1
+2
+3
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chauvin Arnoux PEL105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chauvin Arnoux PEL105 in the language / languages: English as an attachment in your email.

The manual is 11,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info