815482
11
Zoom out
Zoom in
Previous page
1/20
Next page
Vermiculite
Infill
Flaunching
Take Flue Pipe
Up To Narrowest
Part Of Chimney.
150° Elbow
Part No. 010/AV12
Fig. 4. Typical Inset Installation into standard chimney
150°
Fig. 3. Limiting Dimensions Of Surround And Opening
A
B
Dim. A:
Dim. B:
Max. 575mm (22 2/3")
Min. 555mm (21 3/4")
Max. 470mm (18 1/2")
Min. 405mm (16")
The shaded area on the face of
the surround is the minimum flat
area required for Inset Installation.
660 mm
750 mm
®
charnwood
INSTALLATION INSTRUCTIONS SLX20
MU LTI-FUEL
11
order for the appliance to fit into the fire surround there must be a
flat area around the opening, details are shown in Fig. 3.
PREPARATION OF THE FIREPLACE
Before fitting the appliance into an existing fireplace remove the fire
back and any loose in-fill material.
The surround and opening for the appliance must conform with
Fig.3. The flat area around the opening must be a minimum of
750mm wide and 660mm high. Ensure that the hearth and the base
in the opening are flat, level, and at right angles to the surround.
Make a hole in the font of the chimney breast to give access for
infilling and fixing the flue pipe. If the optional boiler is to be fitted it
will also be necessary to make a hole in the side of the chimney
Single wall flue pipe is suitable for connecting the appliance to the breast to give access for the pipework.
chimney but is not suitable for using for the complete chimney.
FITTING THE FIRE
If it is found there is excessive draw in the chimney then a draught
stabiliser should be fitted.
The SLX 20 is supplied with one of two panel packs that makes it
either an Inset stove SLX20i or a Freestanding stove SLX20fs. The
following sections apply specifically to the Inset Installation. The
Freestanding installation is mentioned later.
The appliance must be installed on a fireproof hearth. The
positioning of the appliance and the size of the hearth are governed
by building regulations for Solid Fuel appliances. These building
regulations state that the hearth must extend in front of the
appliance by at least 300mm (12 inches) and to the sides by at least
150mm (6 inches). If in doubt as to the positioning of the appliance,
expert advice should be sought, either from the supplier or the local
building inspector.
The fireplace must allow sufficient airflow around the appliance to
provide combustion air and to allow the heat to be transferred to the
room. The fire surround must be able to withstand the temperatures
generated in normal use. Resin based conglomerates are not suitable
and must not be used. If a wooden mantel is used it should be at least
300mm (12 inches) above the appliance. Wooden surrounds must
be at least 150mm (6 inches) from the sides of the appliance. In
1. INSTALLATION AS AN INSET STOVE
In some cases it may be necessary to place the connecting flue pipe in
the chimney before fitting the fire into the fireplace.
Apply fire cement to the rear face of the sealing flange on the
appliance. Fit the appliance into the opening ensuring that it is central
and that a good seal is made between the sealing flange and the face
HEARTH AND FIRE SURROUND
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood SLX20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood SLX20 in the language / languages: English as an attachment in your email.

The manual is 1.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info