815485

Charnwood SLX 45 MKII - Multi fuel Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
If an existing chimney is to be used it must be swept and checked, it
must be in good condition, free from cracks and blockages, and
should not have an excessive cross sectional area (e.g. greater than
250mm x 250mm). If you find that the chimney is in poor condition
then expert advice should be sought regarding the necessity of
having the chimney lined.
If the stove is fitted in place of an open fire then the chimney should
be swept one month after installation to clear any soot falls which
may have occurred due to the difference in combustion between the
stove and the open fire
If it is found necessary to line the chimney then a lining suitable for
Solid Fuel must be used. If there is no existing chimney then a
prefabricated block chimney or a twin walled insulated stainless steel
flue to can be used either internally or
externally. These chimneys must be fitted in accordance with the
manufacturers instructions and Building Regulations.
Single wall flue pipe is suitable for connecting the appliance to the
chimney but is not suitable for using for the complete chimney.
If it is found that there is excessive draw in the chimney then a
draught stabilizer should be fitted.
BSEN 15287-1:2007
1. INSTALLATION AS AN INSET STOVE
The SLX 45 is supplied with one of two panel packs that makes it
either an Inset stove SLX45i or a Freestanding stove SLX45fs. The
following sections apply specifically to the Inset Installation. The
Freestanding installation is mentioned later.
0
2.0
4.0
6.0
8.0
10.0
2.0
Boiler
Output
(kW)
Space Output (kW)
Fig. 4. Performance Chart
4.0 6.0
Solid Fuel
Wood
HEARTH AND FIRE SURROUND
The appliance must be installed on a fireproof hearth. The
positioning of the appliance and the size of the hearth are governed
by building regulations for Solid Fuel appliances. These building
regulations state that the hearth must extend in front of the
appliance by at least 300mm (12 inches) and to the sides by at least
150mm (6 inches). If in doubt as to the positioning of the appliance,
expert advice should be sought either from the supplier or the local
building inspector.
The fireplace must allow sufficient airflow around the appliance to
provide combustion air and to allow the heat to be transferred to
the room. The fire surround must be able to withstand the
temperatures generated in normal use. If a wooden mantel is used it
should be at least 200mm (8 inches) above the appliance. Wooden
surrounds must be at least 100mm (4 inches) from the sides of the
appliance. In order for the appliance to fit into the fire surround
there must be a flat area around the opening, details are shown in
Fig. 5.
PREPARATION OF FIREPLACE
Before fitting the appliance into an existing fireplace remove the
fireback and any loose in-fill material.
The surround and opening for the appliance must conform with Fig.
5. The flat area around the opening should be a minimum of 750
mm wide and 660 mm high. Ensure that the hearth and the base in
the opening are flat, level, and at right angles to the surround.
Make two holes in the chimney breast, one in the front to give access
for infilling and fixing the flue pipe, and one in the side to give access
for the pipework.
11
Fig. 5. Limiting Dimensions Of Surround And Opening
A
B
Dim. A: Dim. B:
Max. 575mm (22 2/3")
Min. 555mm (21 3/4")
Max. 470mm (18 1/2")
Min. 405mm (16")
The shaded area on the face of
the surround is the minimum flat
area required for Inset Installation.
660 mm
750 mm
®
charnwood
INSTALLATION INSTRUCTIONS SLX4 5
MU LT I-F UEL
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood SLX 45 MKII - Multi fuel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood SLX 45 MKII - Multi fuel in the language / languages: English as an attachment in your email.

The manual is 2.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info