815485
4
Zoom out
Zoom in
Previous page
1/20
Next page
®
charnwood
OPERATING INSTRUCTIONS SLX45
MU LT I-F UEL
4
GENERAL POINTS
When using the fire in situations where children or infirm people are
present please use a fire guard to prevent accidents. The fire guard
should be manufactured in accordance with BS 8423:2010.
FUELS
Coal
When burning bituminous coal a little extra care is needed. Please
take note of the section ‘‘Special Points For Burning Coal’’.
Wood
Only dry well seasoned wood should be burnt on this appliance as
burning wet unseasoned wood will give rise to heavy tar deposits.
Before lighting the fire check with the installer that the work and
checks described in the installation instructions have been carried
out correctly and that the chimney has been swept, is sound, and
free from any obstructions.
Do not light the fire before the boiler and
heating system have been filled with water as this can damage the
boiler.
If the appliance is fitted in place of an open fire then the chimney
should be swept one month after installation to clear any soot falls
which may have occurred due to the difference in combustion
between the appliance and the open fire.
Do not use an aerosol spray on or near the stove when it is alight.
There is a risk of explosion or flash ignition of the spray.
Your SLX45 stove has been designed to work with minimum effort.
If any operation - such as riddling the grate or opening and closing
the door - begins to require extra force then the cause must be
investigated to prev damage being caused to the
stove.
The stove is not suitable for use in a
shared flue system.
ent and correct
Remember that the stove will be hot and is made from hard
material. Ensure that you have good balance before operating the
fire.
The following smokeless fuels are suitable for use on this appliance:
Ancit (Phurnacite Plus), Anthracite Large Nuts, Phurnacite, or any
fuel included on the HETAS list of Approved Smokeless Fuels for
Closed Appliances.
(http://guide.hetas.co.uk/guide/fuels_smokeless.html)
The above fuels are all suitable for use in smoke controlled areas. In
other areas the following fuels may also be burnt:
For the same reason hard wood is better than soft wood. Burning
wet unseasoned wood will also result in considerably reduced
outputs. The wood should be cut and split and then left to season in
a well ventilated dry place for at least one year but preferably two
years before use.
Peat
Ensure that the peat is well dried before use. Burning wet peat will
give rise to heavy tar deposits and reduced outputs.
PETROLEUM COKE IS NOT SUITABLE FOR USE ON THIS
APPLIANCE, ITS USE WILL INVALIDATE THE GUARANTEE
At first you may find it helpful to try several fuels to find the most
suitable. If you are unable to obtain the fuel you want, ask your
supplier or an approved fuel distributor to suggest an alternative or
SLX20
MULTI-FUEL
Operating & Installation Instructions
charnwood
®
C O N T E N T S
O P E R AT I N G I N S T RU C T I O N S
General points
3
SLX20
MULTI-FUEL
Ref. SLX20 10.11
GENERAL POINTS
Before lighting the fire check with the installer that the work and
checks described in the installation instructions have been carried out
correctly and that the chimney has been swept, is sound, and free of
any obstructions. The stove is not suitable for use in a shared flue
Thermostat flap (behind side panel)
Airwash Control
pull to open
Turn handle
clockwise to open
Fig. 1. Controls
Thermostat Control Knob
®
charnwood
OPERATING INSTRUCTIONS SLX20
MULTI -FUE L
3
system.
If the appliance is fitted in place of an open fire then the chimney
should be swept one month after the installation to clear any soot
falls which may have occurred due to the difference in combustion
For Wood
Do Not Go Beyond
45° Position
When Riddling
Riddle Between
Horizontal &
45° Positions
Tool To Be
Horizontal
For Solid Fuel
Vertical
Tool to be
Or Peat
Fig. 2. Grate Operation
®
charnwood
OPERATING INSTRUCTIONS SLX20
MULTI -FUE L ®
charnwood
OPERATING INSTRUCTIONS SLX20
MULTI -FUE L
4
between the appliance and the open fire.
Do not use an aerosol spray on or near the stove when it is alight.
There is a risk of explosion or flash ignition of the spray.
Your SLX20 stove has been designed to work with minimum effort.
If any operation - such as riddling the grate or opening and closing
®
charnwood
OPERATING INSTRUCTIONS SLX20
MULTI -FUE L
5
the door - begins to require extra force then the cause must be
investigated and corrected to prevent damage being caused to the
stove.
Remember that the stove will be hot and is made from hard material.
®
charnwood
OPERATING INSTRUCTIONS SLX20
MULTI -FUE L
6
Ensure that you have good balance before operating the fire.
When using the fire in situations where children or infirm people are
present please use a fire guard to prevent accidents. The fire guard
should be manufactured in accordance with BS 8423:2010.
®
charnwood
OPERATING INSTRUCTIONS SLX20
MULTI -FUE L
7
FUELS
The following smokeless fuels are suitable for use on this appliance:
Ancit (Phurnacite Plus),
®
charnwood
INSTALLATION INSTRUCTIONS SLX20
MULTI -FUE L
8
Fuel Type Wood Logs Smokeless Fuel
Output 5.8kW (19,800Btu/h) 6.3kW (21,500
Flue Gas Mass Flow 5.0 g/s 5.1 g/s
Max Hearth Temp. 90°C 182°C
Re-fuelling Cycle 0.84 hr (50 min) 4.0 hr
CO @ 13% O20.16% 0.18%
Min Distance to
Combustible INSET FREESTANDING
Side 100mm 250mm
Above (inset)/ Rear 300mm 700mm
Min Flue Draft 25Pa (0.1in wg)
Stove Weight 125kg
Add-in Boiler 2.0 kW
Vermiculite
Infill
Flaunching
Take Flue Pipe
Up To Narrowest
Part Of Chimney.
150° Elbow
Part No. 010/AV12
Fig. 4. Typical Inset Installation into standard chimney
150°
Fig. 3. Limiting Dimensions Of Surround And Opening
A
B
Dim. A:
Dim. B:
Max. 575mm (22 2/3")
Min. 555mm (21 3/4")
Max. 470mm (18 1/2")
Min. 405mm (16")
The shaded area on the face of
the surround is the minimum flat
area required for Inset Installation.
660 mm
750 mm
®
charnwood
INSTALLATION INSTRUCTIONS SLX20
MULTI -FUE L
9
Anthracite Large Nuts,
Phurnacite,
Any fuel included on the HETAS list of Approved Smokeless Fuels for
Closed Appliances.
(http://guide.hetas.co.uk/guide/fuels_smokeless.html)
The above fuels are all suitable for use in smoke controlled areas. In
other areas the following fuels may also be burnt:
Coal
®
charnwood
INSTALLATION INSTRUCTIONS SLX20
MULTI -FUE L
10
Vermiculite
Infill
150° Elbow with Welded Socket
Part No. 010/AV37
150mm(6") Class 1 Flue Liner
suitable for Solid Fuel.
Flue Liner Insulation
(see manufacturer’s instructions)
Fig. 5. Typical Inset Installation using Stainless Steel Flue Liner
Alternative Soot Door Positions
Metal Closure Plate
or ‘Register Plate’
With Soot Door
Masonry
Chimney
1
0
4
5
2
3
Fig. 7. Freestanding Installation with Chimney Connection in ‘Inglenook’ type Fireplace
Fig. 6. Freestanding Installation with Chimney Connection above the Fireplace
Alternative
positions for
Soot Door
for sweeping
and debris
clearance
Masonry Chimney
1
0
4
5
2
3
135°
Min
150mm(6") Fluepipe
sleeved through
chimney wall
Old fireplace
filled with non-
combustible material
and bricked up.
Metal Closure
Plate or
‘Register Plate’
Min 700mm from
combustible materials
Recommended min
vertical section 600mm(24")
®
charnwood
INSTALLATION INSTRUCTIONS SLX20
MULTI -FUE L
1112
®
charnwood
INSTALLATION INSTRUCTIONS SLX20
MULTI -FUE L
the
Housecoal Doubles, Trebles or cobbles may all be burnt. Do not use
singles, small nuts, or coal dust. It is important that the large size coal
is used (i.e. Larger than 2” or 50mm in size).
The coal should be dry. When burning bituminous coal a little extra
care is needed. Please Take note of the section “Special Points For
Burning Coal”
Wood
Only dry well seasoned wood should be burnt on this appliance as
burning wet unseasoned wood will give rise to heavy tar deposits. For
Thermostat Flap
Locking Nut
Flap Just Closed With
Knob Set To Minimum
Fig. 9. Thermostat Setting
Drain Cock at Lowest Point
Drain Cock
Gravity Return 28mm
Gravity Flow 28mm
Indirect Hot Water Cylinder
Cold Water Tank
Overflow
Feed and Expansion Tank
22mm Open Vents
Overflow
Domestic Hot Water Draw Off
Fig. 8. Typical Gravity Hot Water System
1
0
4
5
2
3
150°
170
147
608
394
156
i/d
84
265
405
506
547
199
260
548
Knock outs for optional boiler
either side
®
charnwood
SLX 20 DIMENSIONS SLX20
MULTI -FUE L
13
152
395
258(Short Leg)
294
398
152
279
283
(Long
Leg)
Offset Dimensions with 150° Fluepipe 010/AV12 Reversed
607
592(Height to
top of Flue Elbow)
439
86
Flue Centreline
86
142
363
589
506
467
Dimensions for Freestanding Model with 150° Flue Elbow 002/AV13
1
2
3
4
5
0
11 12 18 22 23 24 24 7610 9 8
36
3
5
25
26
1415
1827
19
20
21
38
29
28
13
44
57
57
43
42 57 55 47
48
46
50
49
52
45
51
16
53 54 35
37
17
35
34
30a
33
32a
56 30a
30a
32a
57
Issue F
®
charnwood
SLX 20 PARTS LIST SLX20
MULTI -FUE L
®
charnwood
T: +4 4 (0 )19 83 5 37799 F :+44 ( 0)1983 5 3778 8 SPAR ES@CH ARNWOOD .COM WWW.C HARNWOO D.COM
BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM
Item Part Description
1* 008/KV35S Door Seal Set Inc. Adhesive
2* 008/FW29 Door Seal Adhesive
3 006/KV18 Glass Inc. Glass Channel
4* 008/RW44/S Glass Channel - set of 8
5 004/KV23 Glass Retainer
Item Part Description
29 008/FV49 Thermostat Flap
1415
BSEN 13229:2001
EN13240:2001
A Division of A.J.Wells & Sons Limited Registered in England No. 03809371
11
c h a r n w o o d
Bishops Way, Newport, Isle of Wight PO30 5WS, United Kingdom
A.J WELLS & SONS LTDA.J WELLS & SONS LTD
SLX20
MU LTI-FUEL
ANTHRACITE
0.18%
336°C
6.3kW
72.1%
FREESTANDING
250mm
A D i v i s i o n o f A . J . W e l l s & S o n s L i m i t e d R e g i s t e r e d i n E n g l a n d N o . 0 3 8 0 9 3 7 1
charnwood
T:+44 (0)1983 537777 F:+44 (0)1983 537788 CHARNWOOD@AJWELLS.CO.UK WWW.CHARNWOOD.COM
BISHOPS WAY, NEWPORT, ISLE OF WIGHT PO30 5WS, UNITED KINGDOM
y o u r p r e m i e r d e a l e r
REF SLX20 10.11
®
Graphics on layer 2
9.03 Part no for flue elbow in Fig 5 was 002/AV12
instead of 010/AV12
Telephone & fax number updated.
Logo changed to one with border.
12.03 Hearth and Surround text changed to give more
sensible directions re clearances, in line with Document J
requirements.
03.02.09 Logos updated to current style. Parts List
Added.
10.11 Updated to include Gastec@CRE test results and
CE certificate. Frestanding installation instructions
added.
607
592(Height to top of Flue Elbow)
439
86
Flue Centreline
86
142
363
589
506
467
- Freestanding Model
A12/10/2011
Iss. DESCRIPTION DATE
Alterations
Sheet2 of3
This drawing is the property of A. J. Wells & Sons Ltd.
It may be used only for the purposes for which it
was supplied and may not be copied either whole
or in part without the company's written permission.
© 2011 A. J Wells & Sons Ltd.
Used On
File Name
Drawing No.
Drawn By
Material
Title
Scale
Bishops Way
Newport, Isle of Wight
PO30 5WS, U.K.
Tel: +44(0)1983 537770 Fax:+44 (0)1983 537788
A. J Wells & Sons Ltd.
Tolerance
H:\Xv\
Xv0
Third Angle Projection
All dimensions are in MM unless otherwise stated
PressBrake Program No.
P.A.W.
Est. Weight
XV0
SLX20i General Assembly
1:10
355
378
55
59
50
300
A
A
76
100.5
20
256
287
49
SECTION A-A
- Internal Firebox Dims.
A12/10/2011
Iss. DESCRIPTION DATE
Alterations
Sheet3 of3
This drawing is the property of A. J. Wells & Sons Ltd.
It may be used only for the purposes for which it
was supplied and may not be copied either whole
or in part without the company's written permission.
© 2011 A. J Wells & Sons Ltd.
Used On
File Name
Drawing No.
Drawn By
Material
Title
Scale
Bishops Way
Newport, Isle of Wight
PO30 5WS, U.K.
Tel: +44(0)1983 537770 Fax:+44 (0)1983 537788
A. J Wells & Sons Ltd.
Tolerance
H:\Xv\
Xv0
Third Angle Projection
All dimensions are in MM unless otherwise stated
PressBrake Program No.
P.A.W.
Est. Weight
XV0
SLX20i General Assembly
1:5
This appliance has been approved by HETAS as an intermittent operating appliance for burning dry seasoned wood logs and as a continuous operating appliance burning smokeless fuel.
HETAS approval does not cover the use of other fuels either alone or mixed with wood logs nor does it cover the instructions for use of other fuels.
Thermostat flap (behind side panel)
Airwash Control
pull to open
Turn handle
clockwise to open
Fig. 1. Controls
Thermostat Control Knob
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood SLX 45 MKII - Multi fuel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood SLX 45 MKII - Multi fuel in the language / languages: English as an attachment in your email.

The manual is 2.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info