815490
14
Zoom out
Zoom in
Previous page
1/18
Next page
14
brickwork with vermiculite (e.g. micafil or similar) concrete.
Ensure that there are no air pockets. The recommended mix is
six volumes of vermiculite granules to one volume of Portland
cement thoroughly mixed together. Enough water should be
added so that no more than one or two drops of water are
released when a handful of the mixture is squeezed.
After filling with vermiculite flaunch the top of the flue
connector pipe to the chimney with lime mortar.
Make good the holes in the front and side of the chimney
breast making sure that they are completely airtight. A typical
installation is shown in Fig. 11.
In most installations it will be possible to sweep the chimney
through the appliance. If this is not possible then some
alternative means (such as a soot door), must be provided.
The free inset method of installation may be used instead of
infilling. Details are available on request.
THERMOSTAT
Before lighting the fire check the cold setting distance of the
thermostat.
With the control knob at the maximum setting the flap should
be 18 mm from the air inlet as shown in Fig. 12. To adjust the
distance slacken the locking nut and adjust as necessary. When
set correctly re-tighten the locking nut. Ensure that the flap
opens and closes freely as the knob is turned.
ASSEMBLY
Fit the side panels and hood onto the appliance. Instructions
for this are enclosed with the panel pack. Replace any internal
parts previously removed.
PRE LIGHTING CHECK
Before initial lighting check the following points:
1. The bottom grate bars must all be fitted and should move
freely and easily when the riddling mechanism is operated.
2. The plates round the sides and back of the grate must be in
position and sitting correctly.
3. The throat plate must be fitted in the roof of the appliance
- see Fig. 13.
COMMISSIONING
On completion of the installation and after allowing a suitable
period of time for the fire cement and mortar to dry out, the
fire should be lit and checked to ensure that smoke and fumes
are taken from the appliance up the chimney and emitted
safely. Also check all joints and seals.
The central heating pump should be adjusted to give the
correct water flow against the circuit resistance and the
system should be correctly balanced.
On completion of the installation and commissioning please
leave the operating instructions with the customer and advise
on the use of the appliance and any controls on the system.
FREESTANDING KIT
A freestanding kit is available. Details of dimensions and
outputs are available on request.
®
INSTALLATION INSTRUCTIONS charnwood
Throat Plate
Throat Plate
rests on the
top of the bracket
Fig. 13. Throat Plate Position
Fig. 12. Thermostat Setting
18mm
Thermostat Flap
Locking Nut
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood LA50iB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood LA50iB in the language / languages: English as an attachment in your email.

The manual is 0.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info