Manual Charnwood LA10 (page 6 of 16) (English)

815486

Zoom out

Zoom in

1/16

the grate bars. The ashpan is handled using the tool provided. Care

should be taken to ensure that ash is cool before emptying it into

plastic liners or bins.

To make ash removal easier there is a special Charnwood ash carrier

available. This may be purchased from your supplier or, in case of

difficulty, from ourselves.

For reduced burning the fire door must be closed.

When burning wood in areas that are not smoke controlled, load

some large logs on the fire and allow to burn for half an hour before

closing the front air control slider (this will help to reduce tar deposits

in the chimney.) Leave the airwash control slightly open to help keep

the glass clear. Some experimentation may be necessary to find the

setting most suitable for the type of fuel being used and the draw on

the chimney.

To revive the fire, empty the ashpan, (if burning fuel other than

wood), riddle the fire, and open the air controls to maximum. When

the fire is burning well load on more fuel as necessary and adjust the

air controls to the desired setting.

REDUCED BURNING

MAINTENANCE

Cleaning

Cleaning the Glass

When Not in Use

If the fire is going to be out of use for a long period (for instance in

the summer) then to prevent condensation, and hence corrosion, the

air control should be left fully open and the fire door left ajar. It Is

also advisable to sweep the chimney and clean out the fire. Spraying

The stove is finished with a high temperature paint which will

withstand the temperatures encountered in normal use. This may be

cleaned with a damp lint-free cloth when the stove is cold. Should re-

painting become necessary, high temperature paints are available

from your supplier or from stove shops.

Most deposits on the glass may be burnt off simply by running the fire

at a fast rate for a few minutes. If it becomes necessary to clean the

glass then open the door and allow it to cool. Clean the glass using a

damp cloth and then wiping over with a dry cloth. Any stubborn

deposits on the glass may be removed with a proprietary stove glass

cleaner or ceramic hob cleaner. Do not use abrasive cleaners or pads

as these can scratch the surface which will weaken the glass and cause

premature failure

the inside of the door and firebox with a light oil, such as WD40, will

also help to keep all internal parts working well.

Door Seals

For the fire to operate correctly it is important that the door seals

are in good condition. Check that they do not become worn or

frayed and replace them when necessary.

Servicing

It is recommended that the fire is serviced once a year to keep it in

first class working order. After cleaning out the firebox thoroughly,

check that all internal parts are in good working order, replacing any

parts that are beginning to show signs of wear. Check that the doors

seals are in good condition and that the door seals correctly. A

servicing guide is available on request. Repairs or modifications may

only be carried out by the Manufacturer or their approved agents.

Use only genuine Charnwood replacement parts.

After long periods

where the fire has been out of use, the chimney and appliance

flueways should be cleaned before lighting.

It is important that the throat plate and all the stove flueways are kept

clean in order to prevent potentially dangerous fume emission. They

should be cleaned at least monthly, and more frequently if necessary.

It is necessary to let the fire out to carry out these operations.

The front of the throat plate is pulled forward and then lowered as

shown in Fig. 3. Any sooty deposits should then be swept from the

plate and into the fire.

Return the throat plate to its correct position - raise the front of the

plate, push it back and then lower it onto the retaining lugs.

THROAT PLATE AND

FLUEWAY CLEANING

OPERATING INSTRUCTIONS

Throat Plate

Pull Up

and Swing Down

Fig.3. Throat Plate Position and Lowering

charnwood

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood LA10 in the language / languages: English as an attachment in your email.

The manual is 0.77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Charnwood LA10 Manual

Product: