632311

Charnwood Cove 1 Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
HEALTH & SAFETY PRECAUTIONS
CHIMNEY
This is particularly necessary if the room is double glazed. It must be
positioned such that it is not liable to blockage.
In addition to these instructions the requirements of BS.8303 and
BS EN15287-1:2007 must be fulfilled. Local Authority Bylaws and
Building Regulations regarding the installation of Solid Fuel burning
appliances, flues and chimneys must also be observed, including those
referring to national and European Standards.
Please take care when installing the stove that the requirements of
the Health and Safety at Work Act 1974 are met.
Some types of fire cement are caustic and should not be allowed to
come into contact with the skin. In case of contact wash with plenty
of water.
If there is a possibility of disturbing any asbestos in the course of
installation then please use appropriate protective equipment.
There must not be an extractor fan fitted in the same room as the
stove as this can cause the appliance to emit fumes into the room.
There must be an adequate air supply into the room in which the
appliance is installed to provide combustion air. The combustion air
supply must be via a permanently open vent. There is no requirement
for Cove 1, but minimum free areas are:
16.5cm (2.5 in )
38.5cm (6 in )
In order for the appliance to perform satisfactorily the chimney height
Cove 2
Cove 3
2 2
2 2
must not be less than 4 metres measured vertically from the outlet of
the stove to the top of the chimney. The minimum internal chimney
sizes are as follows:
............ 180mm diameter (7 inches) or 180mm x 180mm
These stoves are to be used in a shared flue. If an existing
chimney is to be used it must be swept and checked, it must be in
good condition, free from cracks and blockages, and should not have
an excessive cross sectional area. If you find that the chimney is in
poor condition then expert advice should be sought regarding the
necessity of having the chimney lined. If it is found necessary to line
the chimney then a lining suitable for Solid Fuel must be used.
If there is no existing chimney then a prefabricated block chimney or
a twin walled insulated stainless steel flue to BS EN15287-1:2007 can
be used either internally or externally. These chimneys must be fitted
in accordance with the manufacturers instructions and Building
Regulations.
Anki pumice liners or chimney blocks will give a highly insulated
chimney which will work well with all fuels. For details ring Anki
Chimney Systems on (01983) 527997.
Single wall flue pipe is suitable for connecting the stove to the
chimney but is not suitable for using for the complete chimney.
If it is found that there is excessive draw in the chimney then a
draught stabilizer should be fitted.
It is important that there is sufficient draw in the chimney and that
the chimney does not suffer from down-draught. When the chimney
is warm the draw should be not less than 0.1 inches water gauge. If in
doubt about the chimney seek expert advice.
The hearth must be at least 12mm (0.5inches) thick. The positioning
of the stove and the size of the hearth are governed by building
regulations for Class 1 appliances. These building regulations state
COVE 1
COVE 2
........... 125mm diameter(5 inches) or 125mm x 125mm
........... 150mm diameter(6 inches) or 150mm x 150mm
Side
Back
COVE 3
NOT
COVE 1 COVE 2 COVE 3
550mm (22in) 450mm (18in) 500mm(20in)
550mm (22in) 600mm (24in) 500mm (20in)
HEARTH AND FIRE SURROUND
The stove must stand on a fireproof hearth and must be situated at
least the following distances from any combustible material:
Specification
Output kW 4.0 8.0 12.0
(BTU/h)
Mass kg
Flue Gas Temp °C 275 300 320
Flue Gas Mass Flow G/s 3.6 6.5 12
Max Hearth 39 25 36
Cove 1 Cove 2 Cove 3
(13,700) (27,300) (41,000)
Low Stand 89 127 159
Store Stand 96 133 171
Centre Stand 104 146 187
Temp °C
SPECIFICATION
The outputs were obtained burning seasoned hardwood over a 1.5
hourly re-fuelling cycle.
®
charnwood
INSTALLATION INSTRUCTIONS
9
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood Cove 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Cove 1 in the language / languages: English as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Charnwood Cove 1

Charnwood Cove 1 User Manual - Dutch - 22 pages

Charnwood Cove 1 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info