815479
12
Zoom out
Zoom in
Previous page
1/28
Next page
12
®
INSTALLATION INSTRUCTIONS
chimney then a draught stabiliser should be fitted. If in doubt about
the chimney seek expert advice.
are governed by
building regulations for solid fuel appliances. If in doubt as to the
positioning of the stove expert advice should be sought either from
the supplier or the local building inspector.
HEARTH AND FIRE SURROUND
The stove must be installed above a fireproof hearth of minimum
250mm depth in accordance with local building regulations, but
ideally 580mm deep to match the projection of the open door. The
positioning of the stove and the size of the hearth
If a wooden mantelpiece or beam is used in the fireplace it should be
a minimum of dimension ‘D’ from the appliance. In some situations it
may be necessary to shield the beam or mantelpiece to protect it.
In order for the appliance to fit into the fire surround there must be a
flat area around the opening. Details are shown in Fig. 10 & 12.
PREPARATION OF FIREPLACE
If the fireplace contains combustible materials, two air vents of 80mm
(Bay 5 & VL) or 100mm (Bay 5GT) diameter must be fitted through
the insulation and the wall of the fireplace to provide a continual air
flow around the stove. Similar vents must be placed between the
closure plate and the top of the stove to ventilate the cavity. It is
recommended that Calcium Silicate board is used (80mm board for
Bay 5 & VL, 100mm board for Bay 5GT), with a 100mm air gap
between the stove and the insulation (see Fig. 11).
If the fireplace does not contain combustible materials, it is still
recommended to have a layer of insulation or ventilate the space
between the casing and the outer wall. The insulation may consist of a
layer of mineral fibre or a vermiculite concrete mix (see Step 4). If
rockwool is being used, insert this into the opening before sliding in
the convection casing.
CONNECTING THE FANS (BAY 5GT ONLY)
The adaptor provided must be connected to a suitable mains socket.
Before fitting the appliance into an existing fireplace remove the
fireback and any loose in-fill material.
The surround and opening for the appliance must conform with
Fig.12. The flat area around the opening should be a minimum of
700mm wide and 600mm high. Ensure that the hearth and the base
in the opening are flat, level, and at right angles to the surround.
For the Bay 5GT, consider where the low voltage power supply for
the fans is to be situated, and install electrical conduit from that point
to back left of the convection casing.
charnwood
BAY
Fig. 10 Minimum Distances from Combustibles
Bay 5 & VL
Bay 5GT
190mm
150mm
250mm
250mm
900mm
1000mm
350mm
460mm
A
Hearth
Mantelpiece
A
B
D
C
From centre of
glass into room
Fig. 11 Air vents and insulation in a fireplace containing combustible
materials
100mm air gap Top of stove
Calcium silicate board
80mm for Bay 5 & VL
100mm for Bay 5GT
Air vent through insulation and
wall of fireplace (Two on each side)
Ø80mm for Bay 5&VL
Ø100mm for Bay 5GT
Fireplace
(Non-combustible)
Dimension A:
Min. 615mm
Max. 650mm
Min. 620mm
Max 650mm
Dimension B:
Min. 410mm
Max. 440mm
Min. 510mm
Max. 540mm
Dimension C:
Min. 380mm
Min. 400mm
Bay 5 & VL
Bay 5GT
Fig. 12 Limiting Dimensions of Surround and Opening
The shaded grey area on the face of the surround is
the minimum flat area required for inset installation.
A
B
C
700mm
600mm
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood Bay 5 GT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Bay 5 GT in the language / languages: English as an attachment in your email.

The manual is 3.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info