Manual Charnwood Arc 7 (page 7 of 24) (English)

694418

Zoom out

Zoom in

1/24

REFUELLING

ASH CLEARANCE

Keep the firebox well filled but do not allow fuel to spill over the top

of the fuel retainer.

Logs should be evenly distributed, filling the firebed to give the most

pleasing flame pattern. The air control must be fully opened after

refuelling until the flames are established above the fire. It is best to

refuel on to a hot bed of embers. If at this point the fire starts to die,

the door must be cracked open until the fire is revived. If the fire has

started to die down before refuelling, then more kindling wood must

be added, the air control opened fully and the door cracked open to

re-establish the firebed before adding larger logs (see suitable log

sizes in Fuel section). This will avoid excessive smoke emission.

Care should be taken, especially when burning wood, that fuel does

not project over the fuel retainer or damage to the glass may be

caused when the door is closed. It can also cause the glass to blacken

up. Maximum filling height is such that logs cannot fall from the fire

when the door is opened.

In smoke controlled areas do not fill the stove above the level of the

air holes in the back bricks, as overloading can cause excess smoke.

Do not operate with the door left open except as directed by the

instructions as this can cause excessive smoke.

For optimum wood burning, it is important to leave a layer of ash

around 1cm thick on the base of the stove. Before removing ash

ensure that it has cooled down,

The ashpan is handled using the operation tool and gloves provided.

Ensure that the tool is fully engaged before lifting (See Fig.4). When

carrying the ashpan, it should be kept horizontal and supported by

the carrying handle to prevent it falling off the tool. Please avoid

emptying hot ash into plastic liners or bins.

The Ashpan should be emptied regularly before it becomes too full.

Never allow the ash to accumulate in the ashpan so that it comes in

contact with the underside of the grate as this will seriously damage

the grate bars.

To make ash removal easier there are ash carriers available. These

may be purchased from your supplier or, in case of difficulty, from

Charnwood.

When not in use the operating tool can be stored inside the store

stand. On the low model the operating tool can be stored on the

shelf underneath the stove. (See fig. 5.)

For reduced burning the fire door must be closed.

When burning wood in areas that are not smoke controlled, load

some large logs on the fire and allow to burn for half an hour before

closing the air control (this will help to reduce tar deposits in the

chimney). Some experimentation may be necessary to find the setting

most suitable for the type of fuel being used and the draw on the

chimney.

Cleaning

Cleaning the Glass

OPERATING TOOL HOLDER

REDUCED BURNING

MAINTENANCE

The stove is finished with a high temperature paint which will

withstand the temperatures encountered in normal use. This may be

cleaned with a damp lint-free cloth when the stove is cold. Should re-

painting become necessary, high temperature paints are available

from your supplier or from stove shops.

Most deposits on the glass may be burnt off simply by running the fire

at a fast rate for a few minutes. If it becomes necessary to clean the

glass then open the door and allow it to cool. Clean the glass using a

damp cloth and then wiping over with a dry cloth. Any stubborn

OPERATING INSTRUCTIONS

Operating Tool

Extra carrying handle

Use with glove

Fig.4 Ashpan

Fig. 5. Operating tool storage

Tool storage underneath

stove on left hand side

(Arc 5 Low only)

Tool storage inside store stand (Arc 5 & 7)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Arc 7 in the language / languages: English as an attachment in your email.

The manual is 3.22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Charnwood Arc 7

Charnwood Arc 7 User Manual - French - 23 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Charnwood Arc 7 Manual

Product: