707656

Charlton Jenrick Fireline Woodtec 5 Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
5 Woodtec Freestanding Issue 01.1 05/17
3.0 Preparation of Stove for Installation.
Your stove comes fully assembled, checked and packed in a protective plywood crate.
Carefully cut and remove the straps and lift off the top and upper crate. Remove any
plastic packaging, open the door and remove all the contents. See List of Components
section (above) and check contents carefully.
**IMPORTANT HANDLING WARNING!!**
NEVER TIP OR ROCK THE STOVE FORWARDS DURING HANDLING AS IT MAY DAMAGE THE
AIR CONTROL LEVER!
3.1. Remove the stove door if required for easier handling of the unit. Open the door,
remove the fixing screws from the bottom hinge and lower the door downwards to
disengage the upper hinge pin. When re-assembling use the same shims that were
factory fitted and make sure that the door is correctly tightened in line with the stove
body.
3.2. Remove the interior components of the stove using the following procedure. SEE ALSO
MAINTENANCE GUIDE section for diagrams where required.
3.2.1. Remove the baffle plate by supporting the plate with both hands and lifting the
front edge upwards towards you and sliding the back edge off the back support and
down slightly into the firebox. Once the rear is lowered then the front edge can also
be lowered off the front baffle supports.
3.2.2. Next remove the two cast ceramic firebox side liners by carefully shifting the
front edges inwards towards the centre of the firebox and sliding forwards away
from the 45 degree mitre joint with the back liner at the rear corners. Take great
care not to chip or damage the surfaces of these ceramic components – support the
rear liner so that it cannot fall over and break!
3.2.3. Now remove the firebox rear liner. Handle and store these ceramic liners very
carefully to one side where they will not get broken.
3.2.4. Remove the firebox base ceramic from the firebox by lifting and tilting.
3.3. Rock the stove to the left and right side in turn and set the adjustable feet of the stove
to approximately their required position. They can be re-adjusted lower later if
required. NOTE: DO NOT rock the stove forward as it may damage the air control
lever!
3.4. The flue spigot collar may now be configured for horizontal connection if required.
3.4.1. Remove the 4 x M6 cap screws in the upper rear firebox and remove the spigot.
3.4.2. Remove the rear casing by levering away from the body at the top with a
screwdriver at the same time as lifting the panel upwards.
3.4.3. The rear casing blanking plate can now be taken out by carefully knocking it out
from the back panel by breaking the provided laser cut micro joints.
3.4.4. Re-fit the back panel before re-fitting the flue spigot.
3.4.5. Finally the spigot may then be rotated by 180 degrees and re-fitted either using
the gasket provided or re-sealing with fire cement as required.
3.4.6. The casing blanking plate can now be used to cover the hole in the top plate.
3.5. Lift the stove into its final position using an assistant to help.
… 6 …


Need help? Post your question in this forum.

Forumrules
1

Forum

charlton-jenrick-fireline-woodtec-5

Reset search

  • where will i locate the SERIAL No of my WOODTEC 5 wood burner for Warranty MANY THANKS Submitted on 17-5-2022 at 18:18

    Reply Report abuse

  • where will i find the SERIAL No on my WOODTEC 5 for the Warranty many thanks P. Loach Submitted on 17-5-2022 at 18:13

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charlton Jenrick Fireline Woodtec 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charlton Jenrick Fireline Woodtec 5 in the language / languages: English as an attachment in your email.

The manual is 1,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info