Manual Char-Broil Platinum 2200S (page 3 of 12) (English, Danish, French, Spanish)

716733

Zoom out

Zoom in

1/12

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of

burner assembly or if you have trouble igniting grill.

1. Turn gas OFF at control knobs and LP cylinder.

2. Remove cooking grates and emitters.

3. Remove carryover tubes.

4. Detach electrode from burner.

5. Carefully lift each burner up and away from valve

openings.

We suggest three ways to clean the burner tubes. Use

the one easiest for you.

A. Bend a stiff wire (a light weight coat hanger works

well) into a small hook. Run the hook through each

burner several times.

B. Use a narrow bottle brush with a flexible handle (do

not use a brass wire brush), run the brush through

each burner tube several times.

C. Wear eye protection: Use an air hose to force air

into the burner tube and out the burner ports. Check

each port to make sure air comes out each hole.

6. Wire brush entire outer surface of burner to remove food

residue and dirt.

7. Clean any blocked ports with a stiff wire such as an open

paper clip.

8. Check burner for damage, due to normal wear and

corrosion some holes may become enlarged. If any large

cracks or holes are found replace burner.

VERY IMPORTANT: Burner tubes must re-engage valve

openings. See illustration below.

9. Attach electrode to burner.

10. Carefully replace burners.

11. Attach burners to brackets on firebox.

12. Reposition carryover tubes and attach to burners.

Replace emitters and cooking grates.

Storing Your appliance

•Clean cooking grates.

•Store in dry location.

•When gas cylinder is connected to appliance, store

outdoors in a well-ventilated space and out of reach

of children.

•Cover appliance if stored outdoors.

•Store appliance indoors ONLY if gas cylinder is turned

off and disconnected, removed from appliance and

stored outdoors.

•When removing appliance from storage check for burner

obstructions.

General appliance Cleaning

•Do not mistake brown or black accumulation of

grease and smoke for paint. Interiors of gas grills

are not painted at the factory (and should never be

painted). Apply a strong solution of detergent and

water or use a appliance cleaner with scrub brush on

insides of appliance lid and bottom. Rinse and allow

to completely air dry. Do not apply caustic

appliance/oven cleaner to painted surfaces.

Høyre

skinne

• Plastic parts: Wash with warm soapy water and wipe

dry.

• Do not use citrisol, abrasive cleaners, degreasers or a

concentrated appliance cleaner on plastic parts.

Damage to and failure of parts can result.

•Porcelain surfaces: Because of glass-like

composition, most residue can be wiped away with

baking soda/water solution or specially formulated

cleaner. Use nonabrasive scouring powder for

stubborn stains.

•Painted surfaces: Wash with mild detergent or

nonabrasive cleaner and warm soapy water. Wipe

dry with a soft nonabrasive cloth.

•Stainless steel surfaces: To maintain your

appliance’s high quality appearance, wash with mild

detergent and warm soapy water and wipe dry with

a soft cloth after each use. Baked-on grease

deposits may require the use of an abrasive plastic

cleaning pad. Use only in direction of brushed finish

to avoid damage. Do not use abrasive pad on

areas with graphics.

• Cooking surfaces: If a bristle brush is used to clean

any of the appliance cooking surfaces, ensure no

loose bristles remain on cooking surfaces prior to

grilling. It is not recommended to clean cooking

surfaces while appliance is hot.

Clean appliance often, preferably after each

cookout. If a bristle brush is used to clean any of the

appliance cooking surfaces, ensure no loose bristles

remain on cooking surfaces prior to grilling. It is not

recommended to clean cooking surface while

appliance is hot.

appliance should be cleaned at least once a year.

•

IF APPLIANCE FAILS TO LIGHT

Make sure gas is turned on at cylinder.

Make sure there is gas in the cylinder.

Does the ignitor make a sparking Noise?

If yes check for spark at burner.

If no spark check for damaged or loose wires.

If wires are OK check for cracked or broken electrode,

replace if needed.

If wire or electrodes are covered by cooking residue,

clean electrode tip with alcohol wipe if needed.

If needed replace wires.

If no sound check battery.

Make sure battery is installed correctly.

Check for loose wire connection at module and switch.

If ignitor continues to not work then use match.

Leak Testing Barb, Hose and

Regulator

1. Turn all appliance control knobs to .

2. Be sure regulator is tightly connected to gas

cylinder.

3. Turn on Gas. If you hear a rushing sound, turn

gas off immediately. There is a major leak at

the connection. Correct before proceeding.

4. Brush soapy solution (mixture of half soap and

half water) onto hose connections.

Leak test before first use, at least once a

year and every time the cylinder is

changed or disconnected.

CAUTION

SPIDER ALERT!

SPIDER AND WEBS

INSIDE BURNER

If your barbecue is getting hard to light or the

flame is weak, check and clean the venturis and

burners.

Spiders or small insects are known to create

“flashback” problems by building nests and laying

eggs in the barbecue’s venturi or burner

obstructing the flow of gas. The backed-up gas

can ignite behind the control panel. This

flashback can damage your barbecue and cause

injury. To prevent flashbacks and ensure good

performance, the burner and venturi tube

assembly should be removed and cleaned

whenever the barbecue has been idle for an

extended period of time.

Turn controls and gas cylinder off when not in use.

Firebox

Carryover

tube

Electrode

Firebox

burner

bracket

Pry off electrode

with a flat blade

screwdriver

Main Burner Ignitor Lighting

Do not lean over grill while lighting.

1. Turn all control knobs to .

2. Turn ON gas at LP cylinder.

3. Open lid during lighting.

4. To ignite, push and turn burner control knob to HI.

5. Push and hold ELECTRONIC IGNITION button

until the burner lights (use flame viewing ports to

verify).

6. If ignition does NOT occur in 5 seconds, turn the

control knobs , wait 5 minutes, and repeat the

lighting procedure.

7. Ignite remaining burners by repeating steps 4 through

6 for each burner.

8. Once each burner has ignited, turn control knobs to

desired setting.

Viewing ports

Main Burner Match-Lighting

Do not lean over grill while lighting.

1. Turn all control knobs to .

2. Open lid. Turn ON gas at LP cylinder.

3. Place match into match holder (hanging from left side

of cabinet). Light match; then light burner by placing

match through the match light hole on left side of grill.

4. Push in and turn far left knob to the HI position. Once

burner has ignited (use flame viewing ports to verify),

turn control knob to desired setting.

5. If ignition does not occur in 5 seconds, turn the control

knob to , wait 5 minutes, and repeat the lighting

procedure.

6. Light adjacent burners in sequence by pushing control

knobs in and turning to the HI position.

WARNING

Correct

burner-to-valve

engagement

5. If growing bubbles appear, there is a leak. Turn off

gas at cylinder immediately and check tightness of

connections. If leak cannot be stopped do not try

to repair. Call for replacement parts.

6. Always turn off gas at cylinder after performing

leak test.

Retainer

clip

Connections

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Char-Broil Platinum 2200S in the language / languages: English, Danish, French, Spanish as an attachment in your email.

The manual is 2,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Char-Broil Platinum 2200S Manual

Product: