555436
35
Zoom out
Zoom in
Previous page
1/44
Next page
34
Operation
Motion Detecting Control Panel (continued)
LOCK
The LOCK feature is designed to prevent activation of the garage door opener from remote controls
while still allowing activation from the door control and keyless entry. This feature is useful for added
peace of mind when the home is empty (i.e.vacation).
l
Activate: Pressand hold the LOCK button for 2 seconds.The command LED will flash as long
as the lock feature is activated and your handheld remote control will not operate your door at
this time.
l
Deactivate: Press and hold the LOCK button again for 2 seconds.The command LEDwill stop
flashing and normal operation will resume.
TIMER-TO-CLOSE
DO NOT enable TTC if operating a one-piece door. The TTC can be turned on or offand the time
interval can be adjusted to 1, 5,and 10 minute intervals. Once the TTC has been setand the door is
open, the selected close interval will blink and begin to count down to close the door.
l
Activate: Pressand hold the ON button until one ofthe TTC LEDslight up. Then press the ON
button again to cycle through the time interval options (the corresponding TTC LEDwill light for
each time interval). The garage door opener lightbulbs will blinkasconfirmation.
l
Deactivate: Press and hold the OFF button until all TTC LEDsturn offand a beep is heard from
the motor unit.
l
Temporarily hold door open (suspend TTC): Press and release the HOLD OPEN button. Press
the HOLD OPENbutton again to resume normal TTC operation.
PROGRAM
Any compatible remote controls,wirelesskeyless entry, or MyQ
®
accessories can be programmed to the
garage door opener by pressing the Learn button.
ON (TTC)
OFF (TTC)
Command LED
Motion Sensor
Switch
LIGHT
Button
HOLD OPEN
Button(TTC)
Motion
Sensor
Push Bar
1, 5, and
10 Minute
TTC LED
LEARN Button
LOCK Button
Remote Control
Your remote control has been programmed at the factory to operate with your garage door opener.
Older Chamberlain remote controls are NOT compatible, see page 40 for compatible accessories.
Programming can be done through the door control or the learn button the garage door opener.To
program additional accessories refer to the instructions provided with the accessory or visit
www.chamberlain.com.Ifyour vehicle is equipped with a Homelink
®
, you may require an external
adapter depending on the make,model,and year ofyour vehicle. Visit www.homelink.com for additional
information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE MOTION-DETECTING CONTROL PANEL
1. Press the LEARNbutton on the door control to enter Programming Mode.
2. Press the LEARNbutton again, the LED will flash once.
3. Remote Control:
Press the button on the remote control that you wish to operate your garage door. Keyless
Entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless entrykeypad.
Then press the ENTER button.
The garage door opener lights will flash (or two clickswill be heard) when the code has been
programmed. Repeat the stepsfor programming additional remote controls or keyless entrydevices.
The command LED
will flash once.
The command LED will
flash once again.
1
2
OR
PIN
? ? ? ?
3
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain WD832KEV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain WD832KEV in the language / languages: English as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info