555436
30
Zoom out
Zoom in
Previous page
1/44
Next page
29
Adjustments
STEP 1 Program the Travel
Without a properlyinstalled safetyreversal system, persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage door.
l
Incorrectadjustmentofgarage door travel limits will interfere with proper operation of safety
reversal system.
l
After ANY adjustments are made,the safetyreversal system MUST be tested. Door MUST reverse
on contact with 1-1/2" (3.8 cm) high object (or 2x4 laid flat) on floor.
While programming,the UP and DOWNbuttons can be used to move the door as needed.
1. Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is heard.
2. Press and hold the UP Button until the door is in the desired UP position.
3. Once the door is in the desired UP position pressand release the Adjustment Button. The
garage door opener lights will flash twice and the DOWNButton will begin to flash.IMPORTANT
NOTE: For one-piece door installations refer to page 28.
4. Press and hold the DOWNbutton until the door is in the desired DOWNposition.
5. Once the door is in the desired DOWNposition press and release the Adjustment Button. The
garage door opener lights will flash twice and the UP Button will begin to flash.
6. Press and release the UP Button. When the door travels to the programmed UP position,the
DOWN Button will begin to flash.
7. Press and release the DOWNButton. The door will travel to the programmed DOWN position.
Programming is complete.
* Ifthe garage door opener lights are flashing 5 timesduring the steps for Program the Travel, the
programming has timed out.Ifthe garage door opener lights are flashing 10 timesduring the steps for
Program the Travel, the safety reversing sensors are misaligned or obstructed (refer to page 27). When
the sensors are aligned and unobstructed,cycle the door through a complete up and down cycle using
the remote control or the UP and DOWNbuttons.Programming is complete. Ifyou are unable to operate
the door up and down,repeat the steps for Programming the Travel.
UP Button
Adjustment Button
DOWN Button
PROGRAMMING BUTTONS
1 2
3
4 5
6 7
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain WD832KEV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain WD832KEV in the language / languages: English as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info