555440
21
Zoom out
Zoom in
Previous page
1/44
Next page
20
Installation
STEP10 Install the door control
To prevent possible SERIOUS INJURY or DEATHfrom electrocution:
Be sure power is NOT connected BEFORE installing door control.
ConnectONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATHfrom a closing garage door:
Install door control within sight ofgarage door, out ofreach of children ata minimum height of5
feet (1.5 m),and away from ALL moving parts of door.
NEVER permit children to operate or play with door control push buttons or remote control
transmitters.
Activate door ONLY when it can be seen clearly,is properly adjusted, and there are no
obstructions to door travel.
ALWAYS keep garage door in sight until completely closed. NEVER permitanyone to cross path
of closing garage door.
INTRODUCTION
Compatible with MyQ
®
enabled accessories,see page 40. Your garage door opener is compatible with
up to 2 MyQ
®
door controls. NOTE: Older Chamberlain door controls and third party products are not
compatible.
Install the door control within sight ofthe door at a minimum height of 5 feet(1.5 m) where small children
cannotreach, and awayfrom the moving parts of the door. For gang box installations itis not necessary
to drill holes or install the drywall anchors.Use the existing holes in the gang box.
NOTE: Your product may look different than the illustrations.
1. Strip 7/16 inch (11 mm) ofinsulation from one end ofthe wire and separate the wires.
2. Connectone wire to each of the two screws on the back of the door control. The wires can be
connected to either screw.Ifyour garage is pre-wired for the door control choose any two
wires to connect, note which wires are used so the correct wires are connected to the garage
door opener in a later step.
3. Mark the location of the bottom mounting hole and drill a 5/32 inch (4 mm) hole.
4. Install the bottom screw,allowing 1/8 inch (3 mm) to protrude from the wall.
5. Position the bottom hole of the door control over the screw and slide down into place.
6. Liftthe push bar up and mark the top hole.
7. Remove the door control from the wall and drill a 5/32 inch (4 mm) hole for the top screw.
8. Position the bottom hole of the door control over the screw and slide down into place. Attach
the top screw.
7/16" (11 mm)
Wall
1
2 3
DRYWALL
GANG BOX
6ABx1"
6-32x1"
Drywall Anchor
4-5
6
6-32x1"
GANG BOX
8
DRYWALL
6ABx1"
Drywall Anchor
7
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain PD752KEV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain PD752KEV in the language / languages: English as an attachment in your email.

The manual is 5,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info