Manual Chacon 34958 (page 5 of 29) (English, Dutch, French, Portuguese, Spanish)

666005

Zoom out

Zoom in

1/29

Stay Mode

Input user code or admin code, and press [Stay Mode] key, the LED

indicator flashes once and the keypad beeps once and sends [Stay

Mode] command to the control panel.

When the alarm panel receives the signal, the siren will beep once

and the [Stay Mode] indicator will light on, the alarm system enters

stay mode state.

All the sensors in other zones are armed to prevent the intruder

except that the motion detector in Home Mode Zone is disarmed,

so that people can move freely at home.

Emergency Call

If not inputting code for SOS is set, user just holds the [SOS] key for

3 seconds, the LED indicator flashes once, the keypad beeps once,

and the control panel alarms immediately.

If inputting code for SOS is set, user needs input user code or

admin code before holding the [SOS] key for 3 seconds to send an

alarm.

Mute Mode

Mute mode means that the LED indicators of control panel flash,

but the siren does not beep, to avoid disturbing the neighborhood.

Input user code or admin code, and hold any key of [Arm] [Disarm]

[Stay Mode] for 2 seconds, the LED indicator flashes once, the

keypad beeps once and sends corresponding command to the

control panel.

When the alarm panel receives the signal, the LED indicator lights

on or off, but the siren does not beep.

Notices and Maintenance

In order to avoid any harm to the users or others during usage and

prolong the usage life, please abide by the following notices.

Usage Notices

General instruction

The keypad should be connected to control panel before use.

The power supply of keypad will probably impact on the

transmitting distance of wireless signal.

The keypad can be powered by 3 pcs of AAA batteries, or wired

by DC 12V.

The keypad is compatible for any our alarm system.

Please remove the battery insulating strip before use.

Do not press SOS key if there's no emergency to avoid disturbing

the neighborhood..

Check the keypad regularly to ensure the system works properly

in case of emergency.

The keypad is neither waterproof nor moisture-proof, please install

it in a shady, cool and dry place.

The case of keypad is made of ABS. Please keep it away from

strong light to ensure the lifetime..

Forbiddance

The keypad is non explosion-proof. Please keep it away from fire,

flame sources.

Install the keypad away from objects such as heater, air

conditioner, microwave oven etc. that produces heat or

electric-magnetic.

Forbiddance of decomposition

Take the keypad for disposal of recycling according to the local

regulation.

Do not take apart the product if you are not a professional

technician.

Maintenance

You can get most dust or fingerprint off with a dry, soft cloth or

tissue. If there is dirt on the keypad, please wipe the surface by a

soft cloth with a little dilute alkaline detergent and then wipe again

with a dry cloth.

FAQ

Problem Cause Solution

No response

from keypad

Low battery Please change the battery

The positive and

negative terminals

are reversed

Follow the right terminal

direction and insert the battery

again

Keypad is locked by

inputting wrong

passcode continually

more than 6 times

Keypad will be unlocked after

non-operation for 20 seconds

Keypad

cannot

connect to

control panel

No response from

alarm panel

Make sure the alarm panel is

powered on

Make sure the alarm panel

enters learning state

Alarm panel beeps

twice

Keypad has been learned

No response

from the

control panel

by operating

on keypad

Keypad is not

learned to control

panel

Please connect the keypad to

the control panel by following

the manual instruction

Distance between

keypad and control

panel is too far

Please move the keypad in a

proper distance where control

panel can receive the signal of

keypad

It’s recommended to buy signal

repeater to extend the distance

Cannot

disarm by

RFID Tags

The RFID tags are

not learned to

keypad

Please connect the RFID tag to

control panel by following the

manual instruction

Disarm by RFID tag

function is

deactivated

Enter setup state and activate

the function of disarm by RFID

tag

Direct disarm by

RFID tag is disabled

Disarm after pressing [*] key

Keypad

cannot be

programmed

Keypad is not waked

Please input [admin code] + [#]

to wake up the keypad

Keypad doesn’t enter

setup state

Please input [admin code] +

[#], and press [3] to enter setup

state

Keypad

cannot be

armed,

disarmed and

in stay mode

Haven't input user

code or admin code

before operation

Please input the user code or

admin code before operation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Chacon 34958 in the language / languages: English, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Chacon 34958 Manual

Product: