664851
5
Zoom out
Zoom in
Previous page
1/28
Next page
Step 1: To power up the Sensor, remove the Battery Tab
Step 2: Perform a Walk Test Sensor
Press the Test Mode button at the back of the sensor to put it in Test Mode.
Place the Sensor in your desired location (don’t use screws at this point), arm the
system and walk in front of the Sensor to test that the Sensor triggers the alarm.
Step 3: Install the sensor
rosneSrosneS
2-2.2m
Ground
Replacing Accessory Batteries
Remote Control
Remove the screw Open the casing
Door/Window Sensor
Open the casing
PIR Motion Sensor
Remove the screw Open the casing
Parallel to the wall
FAQ
Failed to connect to the WiFi
the App, please make sure that your local WiFi network is available and working
properly.
Check that the WiFi name and password are correct.
Connect to a 2.4G WiFi network instead of 5G
Check that the Power Adapter is connected to the Control Panel.
Re-linking the Control Panel to the Router again by following the steps on page 7
The WiFi indicator and the status indicator are on, but I can’t control the alarm by
App
Check that your smartphone is connected to a WiFi network.
Wait a few minutes to see if the WiFi indicator and the status indicator start
Panel is located in an area with good WiFi coverage and then re-pair with your local
WiFi network.
No response from the Control Panel when a Sensor is triggered
The Sensor is not within range of the Control Panel.
Check that the Sensor has been successfully paired to the Control Panel: Press any
Button on the Remote Control, arm the system and separate the Contact from the
Magnetic Sensor or press the Test Button on the Motion Sensor. You can re-pair
the Sensor to the Control Panel by following the instructions in the App – [Edit
Accessories] – [Show Me How]
I can’t Arm or Home Arm (Part Arm) my alarm by App
If the alarm has been triggered and hasn’t been disarmed and a user tries to Arm or
How to delete an Accessory
You can delete any Sensor in the App by going to [Edit Accessories] and tapping
the ‘bin’ icon in the top right hand corner of the screen.
To delete all accessories press and hold the [Learn] button inside the Control Panel
for 3 seconds, the Control Panel will beep once to indicate that all accessories have
been deleted.
No sound when alarming
Check that the Control Panel Alarm volume is not set to mute and the ring time is
not set to ‘0’.
Adjust the volume and the ring time accordingly.
How to reset the alarm system
Press and hold the [WiFi] button inside the Control Panel for 7 seconds.
You will hear one short beep after 3 seconds and then a long beep after another 4
seconds.
The reset has been completed and all the settings have been restored to default
conditions.
Please note that this process does not delete any Sensors.
Delete User (submenu `More') within the App, but make sure the panel has been
connected with WiFi network before the operation.
Control Panel
Power Supply DC 12V 500 mA
Battery 3.7V 600 mAh Li-ion x 1pc
Battery Life Recharge Cycle 300 times
WiFi IEEE 802.11b/g/n
Standby Current <27mA
Alarm Current <180 mA
Internal Siren 85 dB
Optional Accessories 10 Remote Controls, 30 Sensors
Radio Frequency 315 MHz or 433.92 MHz
Housing Material ABS Plastic
Operating Condition
Temperature 0°C~+55°C
Relative Humidity <80% (non-condensing)
Control Panel Dimensions 125 x 150 x 30 mm (L x W x H)
Bracket Dimensions 87.5 x 81.5 x 12 mm (L x W x H)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chacon 34949 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chacon 34949 in the language / languages: English, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 38,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info