664853
4
Zoom out
Zoom in
Previous page
1/23
Next page
Free-standing
The Wall Bracket can also be used as a tabletop stand.
Turn the Wall Bracket upside down so that the arrow is pointing downwards, and
align the screw hole underneath the Control Panel Battery Cover with the screw
hole on the Wall Bracket. Use the remaining screw to secure in place.
Warning:
A weak WiFi signal can seriously affect the performance of this Security Alarm
System. Please make sure that the Control Panel is located as close as possible to
the main Router for optimal connectivity.
Door/ Window Sensor:
Step 1: To power up the Sensor, remove the Battery Tab
Step 2: Attach the Adhesive Pads to the back of the Transmitter and Magnet
Step 3: Place the Sensor on the door/ window frame and the magnet on the door/
window ensuring that the distance between them is not greater than 1cm when the
door/ window is shut.
1cm
PIR Motion Sensor:
Warning - Do not install
O
N
2-2.2m
Ground
Facing direct sunlight
Near air conditioning/ heat
sources
Facing moving objects
Horizontal orientation
Vertical orientation
Replacing Accessory Batteries
Remote Control
Remove the screw Open the casing
Door/Window Sensor
Open the casing
FAQ
Failed to connect to the WiFi
the App, please make sure that your local WiFi network is available and working
properly.
Check that the WiFi name and password are correct.
Connect to a 2.4G WiFi network instead of 5G
Check that the Power Adapter is connected to the Control Panel.
Re-linking the Control Panel to the Router again by following the steps on page 7
The WiFi indicator and the status indicator are on, but I can’t control the alarm by
App
Check that your smartphone is connected to a WiFi network.
Wait a few minutes to see if the WiFi indicator and the status indicator start
Panel is located in an area with good WiFi coverage and then re-pair with your local
WiFi network.
No response from the Control Panel when a Sensor is triggered
The Sensor is not within range of the Control Panel.
Check that the Sensor has been successfully paired to the Control Panel: Press any
Button on the Remote Control, arm the system and separate the Contact from the
Magnetic Sensor or press the Test Button on the Motion Sensor. You can re-pair
the Sensor to the Control Panel by following the instructions in the App – [Edit
Accessories] – [Show Me How]
I can’t Arm or Home Arm (Part Arm) my alarm by App
If the alarm has been triggered and hasn’t been disarmed and a user tries to Arm or
How to delete an Accessory
You can delete any Sensor in the App by going to [Edit Accessories] and tapping
the ‘bin’ icon in the top right hand corner of the screen.
To delete all accessories press and hold the [Learn] button inside the Control Panel
for 3 seconds, the Control Panel will beep once to indicate that all accessories have
been deleted.
No sound when alarming
Check that the Control Panel Alarm volume is not set to mute and the ring time is
not set to ‘0’.
Adjust the volume and the ring time accordingly.
How to reset the alarm system
Press and hold the [WiFi] button inside the Control Panel for 7 seconds.
You will hear one short beep after 3 seconds and then a long beep after another 4
seconds.
The reset has been completed and all the settings have been restored to default
conditions.
Please note that this process does not delete any Sensors.
Delete User (submenu `More') within the App, but make sure the panel has been
connected with WiFi network before the operation.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chacon 34948 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chacon 34948 in the language / languages: English, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 32,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info