780073

Cervelo S3 RIM - 2019 Manual

62
Zoom out
Zoom in
Previous page
1/196
Next page
28
Cut Line
1cm
1cm
1. Taking care to maintain the minimum required seatpost insertion of 6.5cm
and maximum of 8.5cm, carefully measure and use a light coloured grease
pencil to accurately mark the cut-o location on the seatpost.
2. Insert the S Series Seatpost in the Park Tool SG-7.2 Saw Guide (or equivalent)
so that the cut-o line can be seen clearly through the blade guide in the tool.
3. Using a blade designed specically for cutting carbon composite materials (or
a ne tooth blade with greater than 32 teeth per inch); proceed with cutting the
Seatpost (as per Park Tool’s instructions).
4. Use ne grit sandpaper to carefully remove any fraying or burring from the cut
end. Reposition clamp approximately 10cm from the cut end.
5. With a grease pencil, mark a point 1cm from the cut end on the trailing edge
of the Seatpost, and another 1cm from the back, on the bottom edge. Draw a
line connecting them, forming a 45 degree guideline.
6. Placing the blade of your saw on the grease pencil mark, very carefully
proceed to cut, resulting in a 45 degree chamfer being cut onto the trailing
edge of the Seatpost.
7. Carefully sand the end and after applying carbon assembly compound,
return to the frame.
Note: It is essential that all Cervélo Aero Seatposts, have a 45
degree chamfer cut on the rear trailing edge of the post. If trimming
is required after tting, the following method is recommended.
SEATPOST CUTTING INSTRUCTIONS
If trimming is required, final length should allow for a
minimum 6.5 cm of seatpost remaining in the frame.
Failure to meet this requirement, may result in damage
to the frame not covered by warranty policy, or serious
injury to rider.
27
SEATPOST ASSEMBLY
25mm Offset Seatpost
(SP-SP20-25MM)
0mm Offset Seatpost
(SP-SP20-ZERO)
45mm
35mm
M5 Seatpost
Fixing Screws
Actual Size
1. Ensure Loctite 242 is applied to threads
below the head of the 45mm button
head cap screw. Install cross bar on
45mm button head cap screw and
torque to 3Nm.
2. Ensure Loctite 242 is applied to both
xing screw threads.
3. Install the curved washer and
adjustment dial in the seatpost cutout.
4. Install the button head cap screw with
crossbar installed, and turn the dial
until threads are engaged.
5. Install the spherical washer on the
35mm spherical cap screw, so that the
concave face, mates with the convex
surface of the screw.
6. Install cross bar.
7. Apply light coat of carbon assembly
compound to the radius on the upper
face of the seatpost.
8. Install the lower saddle clamp base, as
per the diagram.
9. Locate saddle rails between upper and
lower clamping surfaces.
10. Establish desired saddle angle by rst
using adjustment wheel.
11. Tighten opposing angle adjusting
screw to secure saddle at 8-9Nm.
Button Head
Cap Screw
M5 X 45
Button Head
Cap Screw
M5 X 45
Crossbar
Saddle Clamp
Base
Adjustment
Wheel
Adjustment
Wheel
Spherical
Cap Screw
M5 X 35
Spherical
Cap Screw
M5 X 35 NOTE: The S Series
seatpost is compatible
with both metallic
saddle rails (7mm
diameter) and carbon
saddle rails (7x9mm
cross section).
… 62 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cervelo S3 RIM - 2019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cervelo S3 RIM - 2019 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 44.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info