780081

Cervelo P-Series - 2021 Manual

11
Zoom out
Zoom in
Previous page
1/15
Next page
Cut Line
1cm
1cm
19 20
1. Taking care to maintain the minimum required seatpost insertion of 6.5cm and
maximum of 8.5cm, carefully measure and use a light coloured grease pencil to
accurately mark the cut-o location on the seatpost.
2. Insert the P-Series Seatpost in the Park Tool SG-7.2 Saw Guide (or equivalent) so
that the cut-o line can be seen clearly through the blade guide in the tool.
3. Using a blade designed specically for cutting carbon composite materials (or
a ne tooth blade with greater than 32 teeth per inch); proceed with cutting the
Seatpost (as per Park Tool’s instructions).
4. Use ne grit sandpaper to carefully remove any fraying or burring from the cut
end. Reposition clamp approximately 10cm from the cut end.
5. With a grease pencil, mark a point 1cm from the cut end on the trailing edge of
the Seatpost, and another 1cm from the back, on the bottom edge. Draw a line
connecting them, forming a 45 degree guideline.
6. Placing the blade of your saw on the grease pencil mark, very carefully proceed
to cut, resulting in a 45 degree chamfer being cut onto the trailing edge of the
Seatpost.
7. Carefully sand the end and after applying carbon assembly compound, return
to the frame.
Note: It is essential that all Cervélo Aero Seatposts, have a 45
degree chamfer cut on the trailing edge of the post. If trimming is
required after tting, the following method is recommended.
SEATPOST CUTTING INSTRUCTIONS
If trimming is required, nal length should allow for a minimum 6.5cm of
seatpost remaining in the frame. Failure to meet this requirement, may result
in serious injury to the rider or damage to the frame not covered by warranty.
SEATPOST DI2 BATTERY INSTALLATION
Press the Di2 battery into the Seatpost Battery
Mount (MT-BINT-SP) and attach the E-Wire
according to the manufacturers instructions.
Insert the assembled battery and battery
mount into the seatpost.
P Series Seatpost
Battery Mount
(MT-BINT-SP)
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cervelo P-Series - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cervelo P-Series - 2021 in the language / languages: English as an attachment in your email.

The manual is 5.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info