780083
47
Zoom out
Zoom in
Previous page
1/68
Next page
I General User Manual 47
21.5.2 Vapour bubble formation
Vapour bubble formation can occur if the brakes
are operated continuously for some time, e. g. dur-
ing a long steep descent.
Instead of applying gentle pressure continuously
with the brakes, operate them for shorter periods,
with more force if necessary, releasing the brake
lever intermittently.
Vapour bubbles form if water in the brake uid
heats up, evaporates and forms bubbles in the
brake system.
As these are easily compressed, the brake lever travel
distance increases.
When transporting or storing the bike upside down,
air bubbles can form in the brake system uid reser-
voir.
If you then use the bike, the brakes could fail and
cause a serious accident.
Once the bike is in the correct riding position, pull the
brake lever several times to check whether the brakes
respond normally.
If not, adjust them as follows:
Adjust the brake lever so it is parallel to the ground
and operate it slowly several times so the bubbles
return to the reservoir.
If the response is still poor, the brake system must
be vented. Have this work carried out by a special-
ist cycle shop.
Brake pads and brake blocks are wear parts. Have the
brake pads of hydraulic disc brakes checked regularly,
and replaced if necessary, by a professional bike
workshop.
21.5.3 Cleaning the brake system
If the brake blocks come into contact with oil or grease,
they must be replaced. If the brake disc comes into con-
tact with oil or grease, it must be cleaned as otherwise its
braking performance will be drastically reduced.
Clean and maintain the brake system using isopro-
pyl alcohol, soapy water or a dry cloth. Do not use
commercially available brake cleaning agents or
agents to prevent braking noises as these can dam-
age components such as the seals.
21.5.4 Fitting/removing the wheel
When removing the wheel, we recommend you
use a brake block spacer. This prevents the piston
om being pushed out if the brake lever is oper-
ated once the wheel has been removed. This also
prevents air bubbles in the expansion vessel om
entering the system.
If the brake lever is operated and the brake block
spacer is not inserted, the pistons may extend r-
ther than normal. Put the bike in an upright posi-
tion to push back the brake blocks. Use a clean,
at screw driver or tyre lever and be carel not to
scratch the brake blocks. If the brake blocks are
not tted, push the piston back carelly without
damaging it. If you have trouble pushing back the
brake blocks or piston, remove the reservoir cap
and try again. Note that some oil may ow out the
reservoir.
Aer tting the wheel, check that the quick-release
lever is on the side opposite the brake disc. If it
is on the same side as the brake disc, there is a
danger of the lever and brake disc obstructing one
another and this could also reduce the clamping
force of the quick-release device.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cervelo General - 2012 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cervelo General - 2012 in the language / languages: English as an attachment in your email.

The manual is 10.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cervelo General - 2012

Cervelo General - 2012 User Manual - German - 68 pages

Cervelo General - 2012 User Manual - Dutch - 68 pages

Cervelo General - 2012 User Manual - French - 68 pages

Cervelo General - 2012 User Manual - Italian - 68 pages

Cervelo General - 2012 User Manual - Spanish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info