Manual Celestron SkyProdigy 90 - 22091 (page 8 of 32) (English)

666995

Zoom out

Zoom in

1/32

ASSEMBLY

SkyProdigy comes partially assembled and can be operational in

a matter of minutes. SkyProdigy is conveniently packaged in one

reusable shipping carton that contains the following accesso-

ries:

• 25 mm and 9 mm Eyepieces – 1¼”

• 1¼” Star Diagonal (SkyProdigy 70 and 90 only)

• StarPointer Finderscope and Mounting Bracket

• Deluxe Accessory Tray

• TheSkyX First Light Astronomy Software

• Computerized Hand Control

Assembling SkyProdigy

Your SkyProdigy comes in three major sections: the optical tube,

fork arm and tripod. These sections can be attached in seconds

using the quick release coupling screw located under the tripod

mounting platform and the dovetail mounting clamp located on

the inside of the fork arm. To begin, remove all of the accessories

from their individual boxes. Remember to save all of the contain-

ers so that they can be used to transport the telescope. Before

attaching the visual accessories, the telescope tube and fork arm

should be mounted to the tripod. First, install the accessory tray

onto the tripod legs:

1. Remove the tripod from the box and spread the legs apart

until the center leg brace is fully extended.

2. Locate the accessory tray, and place it on top of the tripod

center support brace in between the tripod legs (see gure

2-1).

3. Rotate the accessory tray so that the central hole in the tray

slides over the ange post in the center of the support

bracket.

4. Finally, rotate the tray so that the locking tabs slide under the

locking clips on the support bracket. You will hear the tray

snap into place.

It is a good idea to level the tripod and adjust the height of the tripod

legs before attaching the fork arm and tube. Minor adjustments can

be made later. To adjust the height of the tripod legs:

1. Loosen the tripod leg locking bolt located on the side of

each leg.

2. Slide the inner portion of each leg down 6” to 8” inches.

3. Adjust the tripod height until the bubble level on the tripod

leg is centered (See gure 2-2).

4. Tighten the tripod locking bolts to hold each leg in place.

Attaching the Hand Control Holder

SkyProdigy comes with a snap-on hand control holder that con-

veniently attaches to any of the tripod legs. To attach the hand

control holder simply position the holder with the square plastic

tab facing up and push against the tripod leg until it snaps into

place (See gure 2-3).

Attaching the Fork Arm to the Tripod

With the tripod properly assembled, the telescope tube and

fork arm can easily be attached using the quick release coupling

screw located underneath the tripod mounting platform:

1. Place the fork arm base inside the tripod mounting platform.

2. Thread the coupling screw into the hole at the bottom of the

fork arm base and hand tighten (See gure 2-4).

INSTRUCTION MANUAL [Continued]

FIGURE 2-1

Flange Post

Locking Tabs

Locking

Clips

FIGURE 2-2

Leveling Tripod

FIGURE 2-3

FIGURE 2-4

Tripod

Mounting

Platform

Coupling

Screw

Fork Arm Base

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Celestron SkyProdigy 90 - 22091 in the language / languages: English as an attachment in your email.

The manual is 3,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Celestron SkyProdigy 90 - 22091

Celestron SkyProdigy 90 - 22091 User Manual - German - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Celestron SkyProdigy 90 - 22091 Manual

Product: