666999

Celestron POWERSEEKER 80 EQ - 21048 Manual

4
Zoom out
Zoom in
Previous page
1/19
Next page
A
A
s
s
s
s
e
e
m
m
b
b
l
l
i
i
n
n
g
g
Y
Y
o
o
u
u
r
r
T
T
e
e
l
l
e
e
s
s
c
c
o
o
p
p
e
e
1) Your Celestron telescope should include all of the following:
a. Tripod with center support bracket
b. Telescope tube with tube rings attached
c. Equatorial mount head
d. Two 1 ¼" eyepieces
e. 90˚ star diagonal
f. 5x24 Finderscope
g. 3x Barlow Lens
h. 5# Counterweight
i. Counterweight bar
j. Two slow motion cables
k. Eyepiece accessory tray
l. The Sky CD rom
2) To set up the tripod, spread the legs outward until they are fully extended. Extend the center portion of each of
the three tripod legs down 6-8". Use the three tightening screws located at the bottom of each leg to secure the
extended legs in place.
3) Place the accessory tray on top of tripod's center leg brace. Thread the tray's threaded post into the threaded
hole in the center of the leg brace.
4) Locate the equatorial mount and place the base of the mount through the hole in the center of the tripod
mounting platform. From underneath the tripod mounting platform, thread the mounting bolt with washer into
the threaded hole on the bottom of the equatorial mount.
5) Thread the latitude adjustment screws into the equatorial mount until both screws are touching the inside of the
mount and the mount can no longer pivot up and down.
6) Locate the counterweight bar and counterweight. Thread the threaded end of the counterweight bar into the Dec
axis of the equatorial mount. Remove the safety screw and washer from the other end of the counterweight bar.
Loosen the counterweight locking bolt so that the screw is no longer obstructing the center hole of the
counterweight. Slide the counterweight half way up the counterweight bar and tighten the locking screw to
secure the counterweight in place. Thread the safety screw and washer on to the end of the counterweight bar.
Figure 1
7) Slide the chrome end of the slow motion control cables onto the equatorial
mount gear shaft. See Figure 1. The longer cable should attach to the Right
Ascension axis and the shorter cable attaches to the Declination axis.
8) Remove the wing nuts from the threaded post at the bottom of the tube ring.
Place the telescope tube on top of the equatorial mount so that the threaded
posts slide through the holes on the equatorial mount. The declination slow
motion cable should extend towards the focuser end of the telescope tube.
Replace the wing nut and tighten to hold the telescope in place.
9) Remove the plastic cap covering the end of the focuser. Loosen the set screw
on the focuser so that it does not obstruct the inner diameter of the focuser.
Insert the chrome barrel of the star diagonal into the focuser and tighten the set
screw.
10) Loosen the set screw on the star diagonal so that it does not obstruct the inner diameter of the barrel. Insert the
chrome barrel of the 20mm eyepiece into the diagonal and tighten the set screw. See Figure 2.
4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron POWERSEEKER 80 EQ - 21048 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron POWERSEEKER 80 EQ - 21048 in the language / languages: English as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info