667000

Celestron PowerSeeker 60EQ - 21043 Manual

27
Zoom out
Zoom in
Previous page
1/151
Next page
27
Aligning the Primary Mirror
Now adjust the primary mirror screws to re-center the reflection of the small secondary mirror, so it’s silhouetted
against the view of the primary. As you look into the focuser, silhouettes of the mirrors should look concentric.
Repeat steps one and two until you have achieved this.
Remove the collimating cap and look into the focuser, where you should see the reflection of your eye in the
secondary mirror.
Newtonian collimation views as seen through the focuser using the collimation cap
Secondary mirror needs adjustment.
Primary mirror needs adjustment.
Both mirrors aligned with the collimating
cap in the focuser.
Both mirrors aligned with your eye
looking into the focuser.
Figure 7-1 PowerSeeker 114EQ
Night Time Star Collimating
After successfully completing daytime collimation, night time star collimation can be done by closely adjusting the
primary mirror while the telescope tube is on its mount and pointing at a bright star. The telescope should be set up
at night and a star's image should be studied at medium to high power (30-60 power per inch of aperture). If a non-
symmetrical focus pattern is present, then it may be possible to correct this by re-collimating only the primary
mirror.
Procedure (Please read this section completely before beginning):
To star collimate in the Northern Hemisphere, point at a stationary star like the North Star (Polaris). It can be found
in the north sky, at a distance above the horizon equal to your latitude. It’s also the end star in the handle of the
Little Dipper. Polaris is not the brightest star in the sky and may even appear dim, depending upon your sky
conditions. For the Southern Hemisphere, point at Sigma Octantis.
Prior to re-collimating the primary mirror, locate the collimation screws on the rear of the telescope tube. The rear
cell (shown in Figure 7-1) has three large thumbscrews (on some models they are not thumbscrews) which are used
for collimation and three small thumbscrews which are used to lock the mirror in place. The collimation screws tilt
the primary mirror. You will start by loosening the small locking screws a few turns each. Normally, motions on
the order of an
1
/
8
turn will make a difference, with approximately a
1
/
2
to
3
/
4
turn being the maximum required for
the large collimation screws. Turn one collimation screw at a time and with a collimation tool or eyepiece see how
the collimation is affected (see the following paragraph below). It will take some experimenting but you will
eventually get the centering you desire.
It is best to use the optional collimation tool or collimating eyepiece. Look into the focuser and notice if the
secondary reflection has moved closer to the center of the primary mirror.
Secondary
Mirror
Primary
Mirror
Mirror Clip
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron PowerSeeker 60EQ - 21043 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron PowerSeeker 60EQ - 21043 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info