666986

Celestron PowerSeeker 60AZ Manual

7
Zoom out
Zoom in
Previous page
1/126
Next page
7
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
T
T
e
e
l
l
e
e
s
s
c
c
o
o
p
p
e
e
T
T
u
u
b
b
e
e
t
t
o
o
t
t
h
h
e
e
M
M
o
o
u
u
n
n
t
t
The telescope optical tube attaches to the altazimuth mount with the altitude slow motion rod assembly and the
respective knobs for the 60AZ, 70AZ and 76AZ. The 50AZ attaches directly to the altazimuth mount head.
Before starting, remove the objective lens cap (refractor) or the front opening cap (Newtonian). To mount the
telescope tube to the mount for the 60AZ, 70AZ, and 76AZ:
1 Remove the protective paper covering the optical tube.
2 Put the telescope optical tube inside the yoke (altazimuth) mount so that the altitude slow motion rod
assembly is on the same side as the altitude locking screw (see Figure 1-1). Note that on some telescopes
that the rod may be attached to the telescope optical tube. If the rod is not attached to the optical
tube, remove the screw from the mechanism (with the provided tool) shown on the far left of Figure
2-7 and put the rod in place as shown in Figure 2-7. Then, put the screw through the hole in the rod
and into the mechanism and tighten it.
3 Thread the altitude locking knob out so the hole is clear in the eyebolt (see Figure 2-8).
4 Put the rod of the assembly through the eyebolt and then tighten the altitude locking knob – Figure 2-9.
5 Thread the two knobs (one on either side of the mount) through the top of the mount into the threaded holes
in the optical tube and tighten – Figure 2-7.
Figure 2-7 Figure 2-8 Figure 2-9
For the 50AZ, take the following steps:
1. Remove the protective paper covering the optical tube.
2. Place the telescope optical tube on the altazimuth mount so that the hole in the top of the optical tube
platform lines up with the holes in the mount head – see Figure 2-11.
3. Insert the altitude locking knob (see center of Figure 2-10) through the mount head and optical tube platform
(make sure the hole is clear all the way through before tightening the knob.
Figure 2-10 Figure 2-11
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron PowerSeeker 60AZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron PowerSeeker 60AZ in the language / languages: English as an attachment in your email.

The manual is 41,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info