667002

Celestron PowerSeeker 114EQ - 21045 Manual

8
Zoom out
Zoom in
Previous page
1/151
Next page
8
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
S
S
l
l
o
o
w
w
M
M
o
o
t
t
i
i
o
o
n
n
C
C
a
a
b
b
l
l
e
e
s
s
The PowerSeeker mount comes with two slow motion control cables that allow you to make fine pointing
adjustments to the telescope in both R.A. and Declination. To install the cables:
1. Locate the two cables with knobs on them. The longer one is for the R.A. axis and make sure the screw on
each cable end does not protrude through the opening.
2. Slide the cable onto the R.A. shaft (see Figure 2-14) so the screw fits over the groove in the R.A. Shaft.
There are two R.A. shafts, one on either side of the mount. It makes no difference which shaft you use since
both work the same (except if using a motor drive). Use whichever one you find more convenient.
3. Tighten the screw on the R.A. cable to hold it securely in place.
4. The DEC slow motion cable attaches in the same manner as the R.A. cable. The shaft that the DEC slow
motion knob fits over is toward the top of the mount, just below the telescope mounting platform.
Figure 2-14
R.A. Shaft on bottom below the R.A. Setting
Circle Dec. Shaft on top above the Dec. Setting
Circle
Figure 2-15
R.A. & Dec. Cables attached
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
T
T
e
e
l
l
e
e
s
s
c
c
o
o
p
p
e
e
T
T
u
u
b
b
e
e
t
t
o
o
t
t
h
h
e
e
M
M
o
o
u
u
n
n
t
t
The telescope optical tube attaches to the equatorial mount with tube rings (except on the 60EQ) supporting it to the
mounting bracket at the top of the mount (Figure 2-16). For the 60EQ refractor, the tube mounts directly to the
mounting bracket with the screw studs attached to the optical tube. Before you attach the optical tube, make sure
that the declination and right ascension locking knobs are tight (Figure 2-24). Then, make sure that the
latitude adjustment screw and latitude locking bolt (Figure 2-27) are tight. This will ensure that the mount does
not move suddenly while attaching the telescope optical tube. Also, remove the objective lens cap (refractor) or the
front opening cap (Newtonian). To mount the telescope tube:
1. Remove the protective paper covering the optical tube. You will have to remove the tube rings (Figure 2-16)
before removing the paper.
2. Remove the knobs from the threaded posts at the bottom of the tube rings (Figure 2-16).
3. Now put the posts through the holes in the top of the mount platform (Figure 2-17) and put the knobs back on
and tighten and they will look like Figure 2-18.
4. Open the tube rings (loosen the large chromed knobs) so that the optical tube can be put on.
5. Hold the optical tube carefully with one hand and center in the tube rings and close the rings and latch and
tighten the knurled knobs of the tube rings which will look like Figure 2-19.
6. Note that you could attach the tube rings to the optical tube first and then attach to the mounting platform on
the equatorial mount as this is a personal preference.
NOTE: Never loosen any of the knobs on the telescope tube or mount other than the R.A. and DEC knobs.
Hint: For maximum rigidity of the telescope and mount, make sure the knobs/screws holding the tripod legs to the
tripod head are tight.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron PowerSeeker 114EQ - 21045 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron PowerSeeker 114EQ - 21045 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info