Manual Celestron Omni XLT 102ED (page 25 of 62) (English)

667013

Zoom out

Zoom in

1/62

The easiest way to polar align a telescope is with a latitude scale. Unlike other methods that require you to find the

celestial pole by identifying certain stars near it, this method works off of a known constant to determine how high the

polar axis should be pointed. The Omni CG-4 mount can be adjusted from about 20 to 60 degrees (see figure 4-3).

The constant, mentioned above, is a relationship between your latitude

and the angular distance the celestial pole is above the northern (or

southern) horizon. The angular distance from the northern horizon to the

north celestial pole is always equal to your latitude. To illustrate this,

imagine that you are standing on the North Pole, latitude +90°. The

north celestial pole, which has a declination of +90°, would be directly

overhead (i.e., 90 above the horizon). Now, let’s say that you move one

degree south — your latitude is now +89° and the celestial pole is no

longer directly overhead. It has moved one degree closer toward the

northern horizon. This means the pole is now 89° above the northern

horizon. If you move one degree further south, the same thing happens

again. You would have to travel 70 miles north or south to change your

latitude by one degree. As you can see from this example, the distance

from the northern horizon to the celestial pole is always equal to your

latitude.

If you are observing from Los Angeles, which is at latitude 34°, then the celestial pole is 34° above the northern

horizon. All a latitude scale does then is to point the polar axis of the telescope at the right elevation above the

northern (or southern) horizon. To align your telescope:

1. Make sure the polar axis of the mount is pointing due north. Use a landmark that you know faces north.

2. Level the tripod. There is a bubble level built into the mount for this purpose.

NOTE: Leveling the tripod is only necessary if using this method of polar alignment. Perfect polar alignment is still

possible using other methods described later in this manual without leveling the tripod.

3. Adjust the mount in altitude until the latitude indicator points to your latitude. Moving the mount affects the angle

the polar axis is pointing. For specific information on adjusting the equatorial mount, please see the section

“Adjusting the Mount.”

This method can be done in daylight, thus eliminating the need to fumble around in the dark. Although this method

does NOT put you directly on the pole, it will limit the number of corrections you will make when tracking an object.

It will also be accurate enough for short exposure prime focus planetary photography (a couple of seconds) and short

exposure piggyback astrophotography (a couple of minutes).

This method utilizes Polaris as a guidepost to the celestial pole. Since Polaris is less than a degree from the celestial

pole, you can simply point the polar axis of your telescope at Polaris (see Figure 4-4). Although this is by no means

perfect alignment, it does get you within one degree. Unlike the previous method, this must be done in the dark when

Polaris is visible.

1. Set the telescope up so that the polar axis is pointing north.

2. Loosen the DEC clutch knob and move the telescope so that the tube is parallel to the polar axis. When this is

done, the declination setting circle will read +90°. If the declination setting circle is not aligned, move the

telescope so that the tube is parallel to the polar axis.

3. Adjust the mount in altitude and/or azimuth until Polaris is in the field of view of the finder.

4. Center Polaris in the field of the telescope using the fine adjustment controls on the mount.

Figure 4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Celestron Omni XLT 102ED in the language / languages: English as an attachment in your email.

The manual is 9,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Celestron Omni XLT 102ED Manual

Product: