580478
9
Zoom out
Zoom in
Previous page
1/54
Next page
Attaching the NexStar to the Tripod
The Celestron NexStar tripod is a sturdy, heavy duty mount on which to place your NexStar 4/5" telescope. This tripod can go
anywhere, from your backyard to a remote observing site and can hold your NexStar in Alt-Az or can be polar aligned with the
use of the built-in equatorial wedge tilt plate. The tripod comes completely assembled and only needs to have the center leg
brace / accessory tray put in place.
Wedge Tilt Plate
Center Support
Rod
Center Leg Brace /
Accessory Tray
Leg Brace Locking
Knob
Telescope Mounting
Bolts
Latitude
Adjustment Rod
Figure 3-5
To set up the tripod:
1. Hold the tripod with the head up, away
from the ground.
2. Pull the legs apart until the legs are fully
extended and press it down flat against
the ground.
3. Place the center leg brace over the center
support rod so that the slotted cutout is
directly under the latitude adjustment rod.
4. Tighten with the leg brace locking knob
until the leg brace firmly presses out
against each leg.
5. The tripod will now stand by itself.
Your tripod has height adjustable legs for
proper leveling on all types of surfaces.
The tripod also comes with detached
bubble level to assist in accurate leveling.
To adjust the height and level the tripod:
1. Place the bubble level on the top of the
tripod tilt plate. Make sure that the tilt
plate is all the way down and horizontal
to the ground.
2. Locate the tightening screw on the
bottom of each tripod leg.
3. Rotate the knob counterclockwise until the inside portion of the tripod leg slides out.
4. Extend the center portion of the tripod leg to the desired height making sure that the bubble in the bubble level is centered..
5. Tighten the knob to hold the tripod leg in place.
If polar aligning your telescope, it is best to adjust the latitude of the wedge tilt plate before mounting the telescope:
1. Loosen the latitude locking lever (located next to the latitude adjustment rod) and raise the wedge tilt plate until the scale on the
latitude adjustment rod is the same as the latitude of your observing site.
2. Tighten the locking lever to hold the tilt plate securely in place.
3. Set the base of the telescope on the wedge tilt plate so that the hole in the center of the base goes over the positioning pin on top
of the tilt plate.
4. Rotate the base so the holes under each rubber foot line up with the mounting bolts attached to the tilt plate.
5. First thread in the mounting bolt closest to the latitude adjustment rod, then align the other two holes and thread in the remaining
mounting bolts. Check that the latitude locking lever is still locked down tight.
Your NexStar is now securely attached to the tripod and ready for use.
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron NexStar 5SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron NexStar 5SE in the language / languages: English as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info